|
| devondevil |
|
|||||
|
Hi guys
I just had my head shaved on my 1994 ef 4.0 & ran into a problem fastening cam back in.I'm having problem getting bolts 4 & 8 (right hand side of pic) back in to hole slots seems to be a metal blockage stopping bolts getting into place,is it ok to drill the holes ? or are there different size bolts/threads tho i do remember having trouble getting them out I remember the bolts being bent from those 2 holes,any advice most appreciated [*]
|
|||||
| Top | |
|||||
| cjh |
|
|||
|
Make sure you have the HLA's in place properly, and the dowel holes are lined up as well.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| Pakrat |
|
||
|
And tighen then all down a little at a time un a spiral to bring the gear down evenly otherwise it'll warp and be a hastle.
But make sure all the HLAs are in correctly and sitting on the valves correctly as mentioned. Don't drill anything for christs sake |
||
| Top | |
||
| devondevil |
|
|||
|
I think you have miss read what I wrote or maybe its the way I wrote it, I can only get 26 of the 28 bolts to sit in the holes even when free standing (no where near the head), holes number 4 & 8 on right hands side in pic, seem to be obstructed & bolts wont penetrate further enough to even touch the head, that's my problem.
|
|||
| Top | |
|||
| cjh |
|
|||
|
devondevil wrote: I think you have miss read what I wrote or maybe its the way I wrote it, I can only get 26 of the 28 bolts to sit in the holes even when free standing (no where near the head), holes number 4 & 8 on right hands side in pic, seem to be obstructed & bolts wont penetrate further enough to even touch the head, that's my problem. Ah..right then.....did you disassemble the rocker gear??? If so, have you assembled it correctly??? If not, then you need to rotate the shafts a little.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| bry40l |
|
|||
|
have you tryed putting the bolts in with all the hla's removed ?
_________________ BF XR6 |
|||
| Top | |
|||
| Pakrat |
|
||
|
If you put a little force down on them will it pop down, sometimes a couple don't sit in like you explained, I usually just give em a oust and they go through tho.
Might have Over heated her |
||
| Top | |
||
| devondevil |
|
|||
|
No cjh
didn't disassemble the rocker gear, new to this job/OHC & that's beyond me what are the hla's ?,will rotate shaft tho & give that a try No didnt over heat the system , tho has I said before 2 bolts 4 & 8 I guess now, was hard to get out because they were bent when dissembling head for shaving. tried putting pressure on bolts but that just damaged thread Some questions might seem trivial but I'd rather ask you guys than go blind & its a great way to learn plus save stuff ups & money and I guess isn't that what this site is all about helping fellow ford owners. thanks guys but I might be back lol |
|||
| Top | |
|||
| cjh |
|
|||
|
HLA's....Hydraulic Lash Adjusters
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| devondevil |
|
|||
|
thx cjh
I'm learning more & more I do a lot of reading & research on here about all subjects. Now, with that shaft how do I rotate it when its inclosed? if I was to tighten down all the other bolts then turn engine over by hand would that rotate the shaft ? kind regards Dino |
|||
| Top | |
|||
| devondevil |
|
|||
|
Hi guys
I managed to get those 2 other bolts in,the amount of force it took by hand was frightening but in & tight thanks all for your advice Dino |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: Google [Bot] and 37 guests |
