|
| 79 raven |
|
|||
|
Looking at an au/ba/bf snorkel going cheap. Genuine Ford item. Will it fit in the Ef Fairmont?
|
|||
| Top | |
|||
| Matt_jew |
|
||
|
Yep.
_________________ xr6turnip wrote: More people paid for a ride in a VT commodore then an AU Falcon so the VT is superior.
Based on that fact my Mum is the best around! |
||
| Top | |
||
| 79 raven |
|
|||
|
Cheers EVL. Once again quick on the buzzer with a short straight answer. You are the man
|
|||
| Top | |
|||
| bry40l |
|
|||
|
Depending which one you get you may have to trim some of the thermo fan shield to fit it properly, I had to when I fitted my bf xr6t snorkel, will be a worthwhile mod on your car though.
_________________ BF XR6 |
|||
| Top | |
|||
| 79 raven |
|
|||
|
Going to see if I can squeeze some cash out for it in the next week, but its under $50 brand new genuine from a Ford dealer, so I will need to get in quick
|
|||
| Top | |
|||
| bry40l |
|
|||
|
79raven wrote: Going to see if I can squeeze some cash out for it in the next week, but its under $50 brand new genuine from a Ford dealer, so I will need to get in quick is that bayford on egay? thats where mine was from
_________________ BF XR6 |
|||
| Top | |
|||
| 79 raven |
|
|||
|
thats the ones, but I read up a bit on here and around the $45 to $50 mark is what they are worth, so I suppose itse not so much of a bargain ( is over the ss s**t). What had to be trimmed ? Was it due to the height of the mouth? Huge difference as mines now a bit over 30mm high and the Bayford ones are 75mm
|
|||
| Top | |
|||
| bry40l |
|
|||
|
where the front of the middle sits against the thermo fans its alot bigger and then you cant get it to line up with the standard air box, so i just chopped the thermo fan gaurd out just enough so it will fit, but no so much the fans are touching the snorkel, i can take a picture during the week for you
_________________ BF XR6 |
|||
| Top | |
|||
| Chargd |
|
|||
|
bry40l wrote: where the front of the middle sits against the thermo fans its alot bigger and then you cant get it to line up with the standard air box, so i just chopped the thermo fan gaurd out just enough so it will fit, but no so much the fans are touching the snorkel, i can take a picture during the week for you bry40l, if you could take a photo that would be great, just wanna compare, how yours sits compared to mine because i used a heat gun and pushed the part that sits against the fan shroud it
_________________ 95 Ef Gli, mods : Tickford Head, Tickford ecu, Pacemaker 4499, Venom 100 cpi cat, Redback 2.5" catback, Wade 977b cam, ba xr6 intake and SS inductions, k & n filter & leather seats. 147.5kw @ wheels |
|||
| Top | |
|||
| efxr6wagon |
|
||
|
The factory AU 6-cylinder snorkel (incl XR6) is probably no better than the stock EF. The EL GT snorkel (may be same as XR8) I think is still available new - is much bigger and a straight 2-minute bolt-in with no trimming required. If you do buy an AU/BA snorkel, go for the XR8/XR6T unit - it is much bigger.
There's a comparison pic here: fordmods-technical-documents-diy-f38/convert-au-to-low-restriction-ba-induction-tube-part-1-t100117.html
_________________ 95 EF XR6 wagon, 17" FTRs, DBA rotors, KYB/Koni, AU bottom end, ported EF head, backcut valves, SS Inductions, Territory intake, 10.2 CR, Auckland 1258 cam, vernier gear, PH4480 headers, no cat, Tickford 2.5", 2800rpm stall, J3 chip |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 49 guests |
