|
| ticky6 |
|
||
|
hey guys got a eb with a ef motor in it i am using all eb management so all the same as a eb would be.
i brought it and got it running runs sweet but just a couple things that i need help with 1: oil pressure guage goes past 7 off the clock any ideas ? matter off switch might be stuffed? just wondering how to fix that 2: theres a white sorter plug on the passenger side towords back the block is that a plug for the ef do i need to use in in the eb ? |
||
| Top | |
||
| SWC |
|
||
|
1) will be a stuffed sender.
2) That will be the knock sensor |
||
| Top | |
||
| ticky6 |
|
||
|
Do I need the knock sensor in eb management ?
Or is it just for the ef it was in ? Thanks heaps |
||
| Top | |
||
| Gab1 |
|
|||
|
ticky6 wrote: Do I need the knock sensor in eb management ? Or is it just for the ef it was in ? Thanks heaps It's not really nessacary, it was just for the EF, leave it unplugged, as for the oil pressure gauge, make sure you are using an EB oil pressure sensor, the EF ones I beleve are different and will be telling the gauge some tall stories. Gab |
|||
| Top | |
|||
| Stealth6 |
|
|||
|
With the oil pressure thing, make sure the wire hasnt come off the sender, My XG did the same. As soon as you turned the key to accessories it shot straight up past seven and stopped their. Got underneath, plugged the wire thing back on and now it works again.
_________________ Yep, I don't know what to write here... |
|||
| Top | |
|||
| ticky6 |
|
||
|
Thanks guys
I will get a eb one  The wires on does both when it's on and off I'm assuming it's a ef one as I don't no what the guy I got the car off did Cheers guys |
||
| Top | |
||
| Esteven8 |
|
|||
|
The EF oil pressure sender is the round looking type about 2" long with a plastic body. From memory the EA/D type are longer hexagonal looking metal bodied thing. And yes, the EF type will give incorrect readings in an EB and vice versa.
_________________ dc_todd wrote: Cheap pads squeal like cheap hookers, and you can take that to the bank. Au Fairmont Ghia My (Old) 95 EF Wagon |
|||
| Top | |
|||
| ticky6 |
|
||
|
hey guys got new oil pressure switch for eb it still doesnt work any ideas now ?
cheers |
||
| Top | |
||
| TROYMAN |
|
||
|
did you fit a oil pressure switch or a oil pressure sender??
2 different things.. pressure switch is for models with the oil light only.( smallish in size) pressure sender is for models with the oil pressure gauge..( rather bulbus and large in size) |
||
| Top | |
||
| ticky6 |
|
||
|
Ahh damit I put smallish switch in lol
Off to sprints tomorrow lol And guys I can't get my timing to stay hook the two spades on diagnostic plug and it's smack on ignition mark as soon as I take tem off its about 20 mm to drivers side car any ideas It's a ef motor with eb management eb series 2 |
||
| Top | |
||
| TROYMAN |
|
||
|
ticky6 wrote: Ahh damit I put smallish switch in lol Off to sprints tomorrow lol And guys I can't get my timing to stay hook the two spades on diagnostic plug and it's smack on ignition mark as soon as I take tem off its about 20 mm to drivers side car any ideas It's a ef motor with eb management eb series 2 thats how it should be, when you have the pins linked in the diagnostic port it puts the ecu in diagnostic mode, this locks the timing into the base setting which in your case is the ign mark.. remove the pins from the diag port and the ecu then controls the timing.. |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 62 guests |
