|
| Chemweeder |
|
||
|
Hey we just finished putting the new auto in my ed, on 1st startup i noticed we had some smoke from the back of the block and coming out of the transmission dipstick we also dropped about 50ml of oil looked like it just ran out of the inspection plate... Any ideas
|
||
| Top | |
||
| Papa Smurf |
|
||
|
Rear Main Seal?
|
||
| Top | |
||
| Nigel |
|
||
|
Torgue Converter / Pump Seal on the gearbox.
Did you have the torque converter on the engine and then mount the gearbox to it?? |
||
| Top | |
||
| Chemweeder |
|
||
|
thx for the input guys we had the TC in the bellhousing for the install, i just had a look at it with a mate weve got no smoke anymore and we noticed after putting it in gear it leaks..like mad but while in park it leaks bugger all
|
||
| Top | |
||
| Nigel |
|
||
|
Does sound like the front pump seal.
Did you pull the converter off the box at all? - anything that could damage it |
||
| Top | |
||
| Chemweeder |
|
||
|
exactly what im thinking now m8 and yes im pretty sure the boys removed it from the gearbox and i dont know if they unbolted the bloody thing off the flywheel... my spider senses are tingling, i think were on a winner here.
|
||
| Top | |
||
| Nigel |
|
||
|
LOL. Its almost impossible to get a trans into the car with the converter mounted on the flywheel WITHOUT screwing it up.
The converter has to be already in the gearbox (use a strap to hold it in, or a bent piece of metal - or something) then mounted to the engine. Then the converter gets pulled forward and the 4 screws done up. Oh - and you'll need a new front seal for the converter. Dont go to Ford. Go to a trans. shop. Much cheaper Nigel |
||
| Top | |
||
| Chemweeder |
|
||
|
thanks nigel, what i meant was i think they left the tc bolted to the flywheel and slid the tranny off... sounded like a good idea at the time get a few mates round for a few beers, darts and mabey an engine and box swap... lol
|
||
| Top | |
||
| Benny D |
|
|||
|
had the same happen to me a few years ago.
unfortunatly its a whole box off again one. i brought a cheap set of various size O ring seals from supershlt and put a fitting one on and was fine.
_________________ BA XT V8. Ice Mint. 18" Speedys. XR6T LSD. Full Pacemaker twin 2 1/2inch Stainless Steel system. Custom CAI. Black XR interior with white trimming. Powerbond underdrive kit 25%. |
|||
| Top | |
|||
| Chemweeder |
|
||
|
well i was thinking over getting it serviced anyway so i might drop it out and take it down to the pros and have them refit the whole shbang. well seeing as were talking you wouldnt happen to know why the engine would be idling high to low (its a steady change up n down) i was thinking it might be because of different computers but i dunno
|
||
| Top | |
||
| tearlejc |
|
||
|
had exact same thing happen putting a new engine in my wifes old corona - thought it had all gone well until it started bleeding everywhere... on those, the seal looks like a combination o ring and metal strip - of course, the only thing that will work is the exact same new bit from toymota.... so....engine cost me $50, did the whole job myself in 3 days - only to have to spend $220 on a new seal that came from japan and took 8 weeks.
_________________ 351 4V XB Coupe running LPG |
||
| Top | |
||
| Chemweeder |
|
||
|
lol similar got given a ed that i diddnt expect to like but did very much, but as it turns out its cheaper to drop in a donor engine and box i picked up a fairmont for $200 with a nice engine all country kms and a few other nice parts so this will most likley be the most expensive part so far
edit* the head for the old motor was going to set me back about $1200 |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 50 guests |
