|
| jake8090 |
|
||
|
Will running a vortech supercharger on 9psi on a untuned motor or wrongly tuned motor cause excessive blow by like blowing the dip stick out or can it wear the rings so much to cause this proberlem. ??
|
||
| Top | |
||
| TROYMAN |
|
||
|
yes, it will.. if the ecu don't cut on boost it will lean out, ping, burn pistons ect..
|
||
| Top | |
||
| GeZza200 |
|
||
|
Was this on the EF falcon or the AU falcon? The AU should boost cut as soon as it reads 1-2psi. The EF will more than likely lean out.
_________________ EL Futura: CVE head, Wolf V500, ICE Ignition and Coil, 36lb injectors, Walbro 255lb, Paci comps, 3" exhaust, T5, Harrop Truetrac with 3.9s. Now with 198.9rwkw, (~185rwkw and 13.80 @99.1mph) with more power to come |
||
| Top | |
||
| jake8090 |
|
||
|
It's au4.0 in a ef falcon if it is tuned right can i run 9psi with a intercooler on a standard low k bottom end with out having a a lot of blow by
|
||
| Top | |
||
| TROYMAN |
|
||
|
if its tuned right it will be fine...
I had au engine in my ed with a turbo running 12-15 psi for near 4 years with no problems , it was only when I went up to 18psi before blow buy stated to be an issue. |
||
| Top | |
||
| galapogos01 |
|
|||
Posts: 1139 Joined: 27th Feb 2005 Ride: Supercharged EF Fairmont Location: T.I. Performance HQ |
If you've already run the car untuned, the damage will already be done. You can't put the magic smoke back into the pistons!
_________________ T.I. Performance - Ford Performance Parts & Tuning - J3 Chips & Tuning, Fuel Pumps & Injectors, Camshafts, Haltech ECUs and more! |
|||
| Top | |
|||
| jake8090 |
|
||
|
Ok cheers
 what bottom end would u recommend for 9psi au or ef ?? I have a standard ef motor in the shed don't really wanna go buy another au bottom end if I don't have to . I have been told au bottom end are balanced a lot better than ef bottoms ends
|
||
| Top | |
||
| bry40l |
|
|||
|
jake8090 wrote: Ok cheers what bottom end would u recommend for 9psi au or ef ?? I have a standard ef motor in the shed don't really wanna go buy another au bottom end if I don't have to . I have been told au bottom end are balanced a lot better than ef bottoms endsthe au runs higher compression than the ef motor, but they are screwed together a little better than the e series motors, for the amount of boost you wanna run either motor would be ok provided they arent already worn out
_________________ BF XR6 |
|||
| Top | |
|||
| GeZza200 |
|
||
|
AU should be smoother revving. The rods will bend easier than the EF rods will though, but with 9psi you will be fine.
_________________ EL Futura: CVE head, Wolf V500, ICE Ignition and Coil, 36lb injectors, Walbro 255lb, Paci comps, 3" exhaust, T5, Harrop Truetrac with 3.9s. Now with 198.9rwkw, (~185rwkw and 13.80 @99.1mph) with more power to come |
||
| Top | |
||
| jake8090 |
|
||
|
Thanks for the help guys
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 14 guests |
