|
| TURBO_GHIA |
|
|||
|
hey guys
does anyone know what sort of pressure the ef el pump puts out . reason i ask is ive modded the pump so it wont leak and im going to mod the hose .prob change it to speed flow fittings etc . cheers guys
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| TimmyA |
|
|||
|
have just had a read of my genuine ford ed manual for the testing of the pump...
It says the special "flow and pressure tester" they made for the job which has a valve on it to increase pressure, connects in series in the pressure line... It says you cannot turn the valve off for more than 5 seconds at a time (pressures must reach breaking point) and says if pressures exceed 1550psi then you need to clean or replace the flow control valve... So if I said the pump is capable of producing 1550psi does that help? See the tests listed below... Attachment: Untitled.png [ 465.09 KiB | Viewed 436 times ] Cheers, Tim
_________________ 93 Red ED 5spd Manual Build Thread |
|||
| Top | |
|||
| TURBO_GHIA |
|
|||
|
yeah that helps thanks mate . looks like i'll be using the teflon hose as its got a higher pressure rating
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| Mad2 |
|
|||
|
TimmyA wrote: have just had a read of my genuine ford ed manual for the testing of the pump... It says the special "flow and pressure tester" they made for the job which has a valve on it to increase pressure, connects in series in the pressure line... It says you cannot turn the valve off for more than 5 seconds at a time (pressures must reach breaking point) and says if pressures exceed 1550psi then you need to clean or replace the flow control valve... So if I said the pump is capable of producing 1550psi does that help? See the tests listed below... Attachment: Untitled.png Cheers, Tim does the EA/B/D do the same?? |
|||
| Top | |
|||
| TimmyA |
|
|||
|
This is for the EA-ED (that's the manual I have...)
EF/EL runs the same pump with a different pulley... Commodores also run this Saginaw pump... Cheers, Tim
_________________ 93 Red ED 5spd Manual Build Thread |
|||
| Top | |
|||
| TROYMAN |
|
||
|
I would be going for a high pressure hydraulic hose, enzed can make them in high pressure braided to suit, without the stupid swivel o ring joint the ef/au have...
|
||
| Top | |
||
| Mad2 |
|
|||
|
so.... i shuld be ok running a AU pump with a EA/B rack?
|
|||
| Top | |
|||
| TimmyA |
|
|||
|
Troyman wrote: I would be going for a high pressure hydraulic hose, enzed can make them in high pressure braided to suit, without the stupid swivel o ring joint the ef/au have... Yep... All they needed was the normal taper seat hydraulic fitting and they would have never leaked... Instead of fitting an O ring seal to a 1500psi system... For some reason Ford decided that they need to have the pipe swivel once it was tight... Even my ED one has never given any trouble... But the EF onward style was rather poor... Cheers, Tim
_________________ 93 Red ED 5spd Manual Build Thread |
|||
| Top | |
|||
| TROYMAN |
|
||
|
Mad2 wrote: so.... i shuld be ok running a AU pump with a EA/B rack? yea it will be fine, other than the different pulley they are the same pump.. |
||
| Top | |
||
| Mad2 |
|
|||
|
good ..... now i just need ta pickup that mota lol
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 52 guests |
