|
| creeture3 |
|
||
|
Hi folks. I want to buy one of these:
http://www.ebay.com.au/itm/Inner-Tie-Ro ... 5d421e898e But I am not sure how to use it. I know the tool slides over the rack end, but I am not sure how to use the "jaws". Does anybody have one of these that can give me a quick lesson? 
|
||
| Top | |
||
| snap0964 |
|
|||
|
How many times will you use it ??
For $20 for a new set of inner tierods, plus what you have left from the $52, get yourself a decent set of vice grips - which will get more use. You can use vice grips to undo and do up the rack ends - when done up, dress the marks off with a file, wash off with metho or similar. Be careful on the drivers side, as the rack is exposed and covered in grease.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| creeture3 |
|
||
|
I will probably use it once or twice, but, against Pedders $230 for replacement of rods, PLUS allignement, total about $300, it's a bargain, and at least I will have it for life.
I think I have figured out how to use it anyway: put the crows foot over the flats on the rod, and slide the "spanner" part up over it into the flats on the spanner |
||
| Top | |
||
| cjh |
|
|||
|
{USERNAME} wrote: Hi folks. I want to buy one of these: http://www.ebay.com.au/itm/Inner-Tie-Ro ... 5d421e898e But I am not sure how to use it. I know the tool slides over the rack end, but I am not sure how to use the "jaws". Does anybody have one of these that can give me a quick lesson? By the looks of it, you select the adapter that fits the rack end, then slide the tool over, fit 2 retaining screws for the adapter, then proceded to undo the rack end. You'll still need a wheel alignment after doing the rack ends anyway.......because you have to take the tie rod ends off to use it.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| snap0964 |
|
|||
|
Wheel alignment is a mandatory. Depends too if you're doing them with the rack in situ - the orientation of the flats will determine if you have room to move, hence vice grips - sounds butcherous, but they do work.
And again, new items for $20 + post from Ebay Suzukisuper would be a good idea. The balls in the existing ones will most likely be a tad loose.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| creeture3 |
|
||
|
Quote: $20 + post from Ebay Suzukisuper Never sure which is better: a $40 item from Repco, or a $20 from somewhere else  You get what you pay for???? |
||
| Top | |
||
| snap0964 |
|
|||
|
Depends who the supplier is - I've bought steering rack seal kits from them @ $45 and be quoted the same kit (same manufacturer) locally here @ $80.
I've bought a fair bit from them over the years, TBH I've found their gear pretty good. I deal with them personally, and have found them very good.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 39 guests |
