|
| DL LTD |
|
|||
|
Aye lads! About to throw some dollars at the 'lane. First thing's first. Got an Explorer to go on. Any thoughts or suggestions on porting/polishing/matching/gasket etc? I've already got AFR 165's to go on as well, possible blower/stroker in future. Any thoughts appreciated
|
|||
| Top | |
|||
| 123esproc |
|
|||
|
Port, polish ,shave, and cam. Trans cooler mini spool high stall etc.
_________________ |
|||
| Top | |
|||
| DL LTD |
|
|||
|
Was thinkin port upper and lower to suit spacer, upper to suit 65mm TB and lower to suit heads. Anything else while its all apart?
|
|||
| Top | |
|||
| 123esproc |
|
|||
|
Valve springs? Oversize injectors bore it out 30 thou oversize lol forged pistons msd ignition then race that b**ch xD
_________________ |
|||
| Top | |
|||
| 67RCE |
|
||
|
Port match the manifold to the heads, spacer and throttle body. Look into a cam swap while the top end is apart, it isn't too much more work at this point.
_________________ ILL60 - EF XR8, Sunroof, Ticky Kit, 19x8.5/19x11 TE37's, 347, AFr185's, TFS BoxRcustom converter, Hurst Quarterstick, huge billet cam. |
||
| Top | |
||
| DL LTD |
|
|||
|
Yeah the only reason i didn't mention cam upgrade yet was that'd mean tune aswell and might blow tha budget bit close to xmas. Thought some 1.7's might do for now?...would definately make sense though...
|
|||
| Top | |
|||
| 67RCE |
|
||
|
In all honesty, small cams, you don't need a tune. I'm running a T3 cam, GT40P's, Explorer, 1.25" Phenolic Spacer, 65mm throttle body and a 70mm MAF on the stock tune.
_________________ ILL60 - EF XR8, Sunroof, Ticky Kit, 19x8.5/19x11 TE37's, 347, AFr185's, TFS BoxRcustom converter, Hurst Quarterstick, huge billet cam. |
||
| Top | |
||
| DL LTD |
|
|||
|
{USERNAME} wrote: In all honesty, small cams, you don't need a tune. I'm running a T3 cam, GT40P's, Explorer, 1.25" Phenolic Spacer, 65mm throttle body and a 70mm MAF on the stock tune. Yeah so she runs alright but obviously not to the full potential? That's ok then. |
|||
| Top | |
|||
| Hickory |
|
||
|
Don't ruin the essence of that car.. It's a Luxo cruiser.. A damn fine car.
Keep it quiet, refined and torquey. I would do the explorer, a full exhaust system, panel air filter,but keep it on the quiet side and a set of 3.45/3.7 diff gears to give it a bit more poke.. Just a set of diff gears will outperform the mild motor work mentioned above and keep it quiet and refined.
_________________ I have been banned for being a knob. |
||
| Top | |
||
| TROYMAN |
|
||
|
considering you already got heads, port matching the manifold would be good imo..
the ports in the explorer are small compared to aftermarket alloy heads. wont make a huge difference but an improvement is an improvement.. |
||
| Top | |
||
| Johnson stroker |
|
|||
|
Heads, cam, manifold, valve springs, throttle body. When going with the manifold, get them to drill it so you can fit your IAT sensor in close to the factory position.
_________________
|
|||
| Top | |
|||
| WARMACHINE |
|
||
|
If you want a cam theres a fellow member here with an E303.
Like has been said match port the lower, throw a phenolic spacer on away you go. I wouldn't do the diff gears until you sort the rest of what you are doing out. Id add a tune with all that and happily run low 14's in a crusier. |
||
| Top | |
||
| Johnson stroker |
|
|||
|
{USERNAME} wrote: If you want a cam theres a fellow member here with an E303. Hmm, I should do something about selling that shouldn't I.
_________________
|
|||
| Top | |
|||
| wild-el |
|
||
|
Sounds like some good mods for when I start my motor
_________________ EL xr6,standard a** au motor,hi-tech headers, 2 1/2inch red back,,Tikky kitted and wingless,Black GT-P's,on ultra lows and still too high |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google [Bot] and 55 guests |
