|
| bondy99 |
|
||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
Hi,
I have a Ford AUII. How does one programme the Remote Keys to work. I've looked at the post regarding BA's I done what was said, and still the remote keys don't work, doors don't cycle . yes, I did press the Rear Demister button 3 times within 5 seconds. Am I doing something wrong or are AUII's have a different way to be programmed? Cheers |
||
| Top | |
||
| Mad2 |
|
|||
|
what did you do when trying to set remotes?. when doing mine i had to do it a few times before it worked
|
|||
| Top | |
|||
| SWC |
|
||
|
You are using the correct procedure.
As Mad2 has said, it sometimes takes a few trys to get it to got into program mode. |
||
| Top | |
||
| bondy99 |
|
||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
G'day I'm sure I did.
Procedure I used is this 1. Close all doors. 2. Turn key to ACC 3. Press demister button 3 times within 5 seconds 4. Press "Open door icon" on remote. Doors should cycle open and close 5. Repeat step for second remote. 6. Good to go. Or should I pressing the demister button as in 3 cycles within 5 seconds i.e. Press 1 light on, press 2 light off, press 3 light on, press 4 light off, press 5 light on, press 6 light off , within 5 seconds. |
||
| Top | |
||
| Robert_au |
|
|||
|
{USERNAME} wrote: G'day I'm sure I did. Procedure I used is this 1. Close all doors. 2. Turn key to ACC 3. Press demister button 3 times within 5 seconds 4. Press "Open door icon" on remote. Doors should cycle open and close 5. Repeat step for second remote. 6. Good to go. Or should I pressing the demister button as in 3 cycles within 5 seconds i.e. Press 1 light on, press 2 light off, press 3 light on, press 4 light off, press 5 light on, press 6 light off , within 5 seconds. Its just the 3 fast presses in 5 seconds press press press The door locks should cycle to indicate learning mode has been entered. try doing what you have but waiting 5 or 10 seconds before you press any buttons on the remotes.
_________________ Current Ride |
|||
| Top | |
|||
| Mad2 |
|
|||
|
{USERNAME} wrote: G'day I'm sure I did.
Procedure I used is this 1. Close all doors. 2. Turn key to ACC 3. Press demister button 3 times within 5 seconds 4. wait for door locks to cycle if no - turn off key & try again if yes - proceed to next step 5. Press "Open door icon" on remote. Door locks should cycle close and open 6. Repeat previous step for second or more remotes [up to 8?]. 7. finished turn vehicle off & exit vehicle. |
|||
| Top | |
|||
| bondy99 |
|
||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
Hi,
Ok, i'll do that next time (tomorrow morning). Question regarding ACC. Is that the position prior start as in run? The ACC position indicator is either worn off or is not marked on my ignition switch. Cheers |
||
| Top | |
||
| TedW |
|
||
|
acc. is one position up from lock position-
one position before reds push demist within 5 sec of turning to acc wait a couple of sec after pushing demist 3 times for locks to operate does central locking work ? |
||
| Top | |
||
| bondy99 |
|
||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
@ TedW,
Thanks for your message. I assume lock position is when the key can be withdrawn. I'm sure I had the key in acc position but will double check again. Sorry, I don't know what "reds" is Central locking works with the door key and opens up with the old remote key. The old remote key's lock button no longer works. The cradle that holds the battery in position broke off sometime ago. I've been trying to get those 2 new remote keys trained to work properly. |
||
| Top | |
||
| SWC |
|
||
|
Ignition Lock has 4 positions;
1) Off - Locked (key can be removed) no power on. 2) Acc - Accessories (key cannot be removed) power to accessories, radio, power windows etc. 3) Ignition on - Reds. Power to engine components, Dash warning lights are on, hence to reference to "REDS". 4) Start - starter motor on. Momentary contact, springs back to Ignition on when released. |
||
| Top | |
||
| bondy99 |
|
||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
@ SWC,
Thanks for clarification. Just to let everyone else know, finally got the two remote keys trained. I don't know why it did not work previously but this time with the additional pause of about 10 seconds, doors cycled and remote keys tuned. Thanks for your help. Cheers |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 38 guests |
