|
| sliding6 |
|
||
|
Hey guys just wondering whats involved in setting up a log mani from an early e series instead of running the bbm in my el as i have heard this is the way to go when boosting. Anything else needed apart from the manifold itself? Wiring? Any help appreciated
Thanks heaps |
||
| Top | |
||
| Mad2 |
|
|||
|
from what i understand the tensioner will need to be changed to the XG/XH style [not the XR6 version] so it don't foul on the intake manifold. i'm currently thinking of fitting one but the $$ for said item has put me off a little. will get around to fitting the log onto a AU motor i have here to see whats what....
 good luck with the turbo Ps. the BA etc have the turbo's fitted from factory with 'standard' intakes ... only mod is removal of the runner blades [change the runner lengths] from what i've read? |
|||
| Top | |
|||
| Robert_au |
|
|||
|
Mad2 wrote: Ps. the BA etc have the turbo's fitted from factory with 'standard' intakes ... only mod is removal of the runner blades [change the runner lengths] from what i've read? correct there Mad2, the BA/BF did use the BBM with the butterflys removed from factory. The butterflys could be removed from your manifold, you would need to get the "holes" welded up where the shaft went through and mating surfaces machined flat again.
_________________ Current Ride |
|||
| Top | |
|||
| Mad2 |
|
|||
|
Robert_au wrote: Mad2 wrote: Ps. the BA etc have the turbo's fitted from factory with 'standard' intakes ... only mod is removal of the runner blades [change the runner lengths] from what i've read? correct there Mad2, the BA/BF did use the BBM with the butterflys removed from factory. The butterflys could be removed from your manifold, you would need to get the "holes" welded up where the shaft went through and mating surfaces machined flat again. would there be any problem leaving the shaft there 'bare' 
|
|||
| Top | |
|||
| Robert_au |
|
|||
|
Mad2 wrote: Robert_au wrote: Mad2 wrote: Ps. the BA etc have the turbo's fitted from factory with 'standard' intakes ... only mod is removal of the runner blades [change the runner lengths] from what i've read? correct there Mad2, the BA/BF did use the BBM with the butterflys removed from factory. The butterflys could be removed from your manifold, you would need to get the "holes" welded up where the shaft went through and mating surfaces machined flat again. would there be any problem leaving the shaft there 'bare' Properly not actually as long as it didn't leak under boost that would be my only concern and the likely annoying whistle 
_________________ Current Ride |
|||
| Top | |
|||
| TROYMAN |
|
||
|
i experimented with the butterflies in the au manifold in my turbo ed and with them removed it made no difference in peak power at all, but with them in and operational it made significantly more low end torque and especially at the point of spool up with the same peak power..
imo ,overall it was much better with the butterflies operating.. |
||
| Top | |
||
| sliding6 |
|
||
|
So far i think ill need the xh tensioner and throttle cable.
Main reason for converting is i dont want to run cooler piping all the way up and around the bbm to the throttle body. Not sure if ill need any wiring or vac lines from a wreck along with the log mani |
||
| Top | |
||
| Mad2 |
|
|||
|
sliding6 wrote: So far i think ill need the xh tensioner and throttle cable. Main reason for converting is i dont want to run cooler piping all the way up and around the bbm to the throttle body. Not sure if ill need any wiring or vac lines from a wreck along with the log mani i got a quote of $345.00 plus postage for a brand spankers 
|
|||
| Top | |
|||
| Mad2 |
|
|||
|
Mad2 wrote: sliding6 wrote: So far i think ill need the xh tensioner and throttle cable. Main reason for converting is i dont want to run cooler piping all the way up and around the bbm to the throttle body. Not sure if ill need any wiring or vac lines from a wreck along with the log mani i got a quote of $345.00 plus postage for a brand spankers have found another for $198 delivered |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 52 guests |
