|
| MadMatt |
|
|||
|
J3 chip with manual tune?
_________________ Member Number 8804 |
|||
| Top | |
|||
| The Dog |
|
|||
|
Thinkin' about that but there has to be an easier (and cheaper) way.......
_________________ You'll ride a black tornado across the western sky
|
|||
| Top | |
|||
| BenJ |
|
||
|
The fans are running all the time as the ECU thinks the Auto Tranny is overheating. That is one of the lines you need to add the resistors too.
The reason it is idling so high, is you need to tell the auto ECU that it is in neutral, which is the other line you need to add resistors. There is a guide in the Technical Documents Forum with the details re what resistors to use. http://www.fordmods.com/fordmods-technical-documents-diy-f38/auto-to-manual-conversion-guide-t42420.html As for the miss, I doubt that is ECU related, and is more likely to be spark related. Are all the plugs, leads, dizzy cap, rotor button and coil in good condition? BenJ
_________________ BenJ's EB T5 DOHC Ghia Wagon - Current Ride |
||
| Top | |
||
| snap0964 |
|
|||
|
Mine's a factory manual, but I'm running an auto ECU.
Mine has both auto and manual looms into the engine bay. What you should do is disconnect the manual transmission neutral switch, and fit the resistor to the two terminals on the loom. Next is transfer the drive gear off the EF cam angle sensor that came with the engine onto your dizzy. I suspect otherwise you'll have Aux shaft issues like most of these guys are having with the AU engine install/dizzy setup.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| The Dog |
|
|||
|
Thanks Snap. Asked the Jaycar distributor over at Naracoorte about a 7ohm resistor and he reckoned there was no such critter but he could sell me a 6.8. Is that close enough to do the trick?
I take it the cam angle sensor is where the dizzy would normally sit? This bit didn't come with the engine but I can source one. What issues will it create by not having it?
_________________ You'll ride a black tornado across the western sky
|
|||
| Top | |
|||
| snap0964 |
|
|||
|
6.8kohm will be fine.
1.2kohm for the trans temp. Might be able to get a new gear from ford - aftermarket ones seem to fail. Do a search on 'auxilliary' and 'auxiliary' - been covered a few times.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| 1tuff |
|
||
|
Close to what im doing. Ive got an xg ute im pulling the motor out of and putting in a el xr6 motor. The ute is a manual and im putting in a el xr6 manual computer. Will i need to change the looms over for the bbm manifold ordo i just need to plug in a few extra wires into my exsiting loom to hook in the bbm manifolds butterfly?
_________________ To many project's and not enough $$$ |
||
| Top | |
||
| snap0964 |
|
|||
|
snap0964 wrote: add the extra wire to run the BBM solenoid valve plus IGN 12 v.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| 1tuff |
|
||
|
Thanks snap
_________________ To many project's and not enough $$$ |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 50 guests |
