|
| bondy99 |
|
||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
Does anyone know where I can get a cheap priced taillight loom for Ford AUII?
Left side brake light holder that holds the globe cracked where the bulb pins are held. Bulb was rattling inside taillight. I tried local wreckers, no joy, all wires have been removed. Ebay no joy, not paying $95.00 for a loom. I take it this must be a common fault with Ford AU's? |
||
| Top | |
||
| Papa Smurf |
|
||
|
Here is one that is $43.00 and is near to you:
http://www.ebay.com.au/itm/Genuine-Au-F ... SwfJJZaLDG MAYBE, this one? hard to tell: http://www.ebay.com.au/itm/FORD-FALCON- ... Sw3ydV4nS8 You might also get away with using a BA one? not sure as I don't have both to check out. They are cheaper for some reason? http://www.ebay.com.au/itm/Ford-Fairmon ... 0009.m1982 |
||
| Top | |
||
| bondy99 |
|
||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
Papa Smurf.
Thanks for your help mate, That BA one looked very similar to mine. maybe there is some commonality in the wiring look, tail lights at least. That second link is identical to what my taillight is. |
||
| Top | |
||
| TedW |
|
||
|
Try auto elect. or supercheap or similar for replacement socket and solder to wiring
Check it works before soldering |
||
| Top | |
||
| bondy99 |
|
||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
Supercheap don't stock any.
If the socket is made from bakerlite then it will go brittle over the years and easily crack, so I'm told. It would be good if one knows who manufactured those sockets, one can buy a few sockets bit cheaper. |
||
| Top | |
||
| Mad2 |
|
|||
|
{USERNAME} wrote: Supercheap don't stock any. If the socket is made from bakerlite then it will go brittle over the years and easily crack, so I'm told. It would be good if one knows who manufactured those sockets, one can buy a few sockets bit cheaper. doubt very much that it's "bakerlite" & plastic has more chance of going brittle 1st. |
|||
| Top | |
|||
| bondy99 |
|
||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
It's not metal , so must be hard plastic then
|
||
| Top | |
||
| 93EB |
|
|||
Age: 47 Posts: 2486 Joined: 6th Oct 2005 Ride: 93EB Fairmont / BA Falcon XR6T Location: Western Sydney |
I had same issue with my dads AU. Got a socket with some loom from a wreckers and soldered it on to the existing loom
_________________ 93 EB II Fairmon8 with 17' EL GT's / Clear indicators / H.I.Ds / Sports exhaust / Lowered 2' / K&N / XR6 ECU. |
|||
| Top | |
|||
| snap0964 |
|
|||
|
^^^ simplest and easiest way. You have a choice of AU/BA/BF wagons to source.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| bondy99 |
|
||
Age: 65 Posts: 1128 Joined: 13th Sep 2010 Ride: Ford Falcon AU 2000 Series II Location: Crestmead |
Thanks fellas,
I'll be doing that, hopefully not all models have had their taillight looms removed. I'll be soldering plug to existing wires if need be (worse case scenario) Thanks |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 53 guests |
