Fordmods Logo

nos installation 

 

Page 2 of 2 [ 29 posts ] Go to page Previous  1, 2

 
Posted: Thu Jun 23, 2005 8:51 pm 
Getting Side Ways
Offline

Age: 39

Posts: 1112

Joined: 18th Jan 2005

Location: MAFFRA
VIC, Australia

will there be disadvantages to running a standard fuel pump and no pressure reg?

 

_________________

97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump

Top
 Profile  
 
 
Posted: Thu Jun 23, 2005 9:27 pm 
Getting Side Ways
Offline

Age: 39

Posts: 1112

Joined: 18th Jan 2005

Location: MAFFRA
VIC, Australia

also how much more difficult is a wet kit to install and use?cant seem to find many dry kits around but heaps of wet kits

 

_________________

97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump

Top
 Profile  
 
 
Posted: Fri Jun 24, 2005 2:33 am 
Getting Side Ways
Offline
User avatar

Age: 71

Posts: 3555

Joined: 7th Nov 2004

Gallery: 4 images

Power: 482 rwkw

Location: Penrith
NSW, Australia

madeaspack wrote:
will there be disadvantages to running a standard fuel pump and no pressure reg?

There is one there.[But not rising rate]..Rising rate regs are not expensive..May save engine..Saves all the B.S with wet system as it richens mixture anyway..It wont effect mixture when not runing n20....

 

_________________

As in ZOOM 126 edition
331 Dart block,3.25/ 4340 steel crank, Oliver rods,TFS ported track heat heads, TFS track heat inlet Twin SC61 turbo's
Project 1UZ-EF has started.. S475 Turbo 4.0 V8 Mustang Celica.....

Top
 Profile  
 
 
Posted: Tue Jul 05, 2005 10:40 pm 
Parts Gopher
Offline

Posts: 86

Joined: 10th Nov 2004

Ride: No fords at the mo' :-(

Location: Sydney
NSW, Australia

Hey there EBXR8380 .... you mention the use of a rising rate 2:1 fuel pressure reg ... aren't these boost indexed or related to manifold pressure some how? How would one of these be set up on a NA + Nitrous engine?

I am curious as I would consider one of these for my project ...

Cheers

 

_________________

Chasing 162mph on the Salt! 4.2L. Both race cars now sold! :-( Maybe a small-block tractor puller! or a Lotus 7 Clubman is next! or a 351-stroker powered EB ... ?

Top
 Profile  
 
 
Posted: Thu Jul 07, 2005 6:06 pm 
Getting Side Ways
Offline
User avatar

Age: 53

Posts: 3763

Joined: 25th Nov 2004

Gallery: 6 images

Ride: EFII 5.8 NOS TerroristGhia

Power: 274 rwkw

Location: Sydney Australia
NSW, Australia

There is a line that comes from the solenoid on the kit that feerds into the fuel reg via a t-piece and this is how the pressure increases. Once the solenoid is activated the reg gets bottle pressure and that increases the mixtures
Brett

 

_________________

The Terrorist ED Retired due to RUST.
The TerrosistGhia, EF Ghia 351 EFI 5 Speed.
Millennium Falcon, Sleeper EL DOHC 6 Speed Manual EFI LPG
Member#1131
I didn't Vote for Multiculturalism, DID YOU!!!

Top
 Profile  
 
 
Posted: Thu Jul 07, 2005 6:25 pm 
Getting Side Ways
Offline
User avatar

Age: 43

Posts: 8655

Joined: 5th Nov 2004

Gallery: 37 images

Ride: V8 EF Futura

Location: Adelaide CBD
SA, Australia

What kind of pressure does the nos line run at brett?

 

_________________

I promise..... I will never die.

Fordmods Administration Group MINOR PUNKED

Top
 Profile  
 
 
Posted: Thu Jul 07, 2005 7:06 pm 
Parts Gopher
Offline

Posts: 86

Joined: 10th Nov 2004

Ride: No fords at the mo' :-(

Location: Sydney
NSW, Australia

Thanks. Cool!

I am looking into this N20 thing ....

100hp dry kit could be the go for sure .....

I think I will add an uprated fuel pump too .....


Cheers

 

_________________

Chasing 162mph on the Salt! 4.2L. Both race cars now sold! :-( Maybe a small-block tractor puller! or a Lotus 7 Clubman is next! or a 351-stroker powered EB ... ?

Top
 Profile  
 
 
Posted: Thu Jul 07, 2005 8:31 pm 
Getting Side Ways
Offline
User avatar

Age: 53

Posts: 3763

Joined: 25th Nov 2004

Gallery: 6 images

Ride: EFII 5.8 NOS TerroristGhia

Power: 274 rwkw

Location: Sydney Australia
NSW, Australia

Stock pressure is about 42psi, when its activated jumps to about 70psi, all on the stock regulator. I have mine set at 38psi and have a hobbs switch to kill the NOS if it drops below 55psi. This is an optional extra from NOS, and is also tuneable
Brett

 

_________________

The Terrorist ED Retired due to RUST.
The TerrosistGhia, EF Ghia 351 EFI 5 Speed.
Millennium Falcon, Sleeper EL DOHC 6 Speed Manual EFI LPG
Member#1131
I didn't Vote for Multiculturalism, DID YOU!!!

Top
 Profile  
 
 
Posted: Sat Jul 23, 2005 9:10 pm 
Getting Side Ways
Offline
User avatar

Age: 37

Posts: 593

Joined: 5th Nov 2004

Gallery: 13 images

Location: Melbourne
VIC, Australia

stuff the dry kit, go the WET thats what i got, and im running stock fuel system and im just running different plugs, you will find it's easyier after it's installed, if it ever runs lean on NOS then just put a bigger fuel jet in, if it ever runs rick put a smaller one in, and with a wet shot you can go higher then 100 shot and be safe, just have to mess around with timing and how bigger fuel jet you have in there.
and yes start off at a low jet 1st or your engine could blow, i did a mistake of doing a 150hp shot 1st up, we put it down to a 50 hp shot a few weeks later and it pinged even at 50hp shot, but after putting timing back, and putting a bigger fuel jet then reccomended for the shot all was fine.

i also have a bottle heater, in cabin remote bottle opener, and a purge kit, but i would at least reccommend a heater, maily if you live in a cold area tho, but you want to save money and you live in a hot area then a blanket will do fine.

 

_________________

4 cylinders are like chinese food, few minutes after you have them you just want more!

Top
 Profile  
 
 
Posted: Wed Jul 27, 2005 1:24 am 
Smokin em up
Offline
User avatar

Age: 39

Posts: 297

Joined: 5th Nov 2004

Ride: 410 Cube FE LTD

Location: Canberra
ACT, Australia

how do you go about setting up a NOS kit on a Carby fed V8? is it easier, and which kits should be used for carby v8s?
Top
 Profile  
 
 
Posted: Wed Jul 27, 2005 11:48 am 
Getting Side Ways
Offline

Age: 41

Posts: 3405

Joined: 7th Feb 2005

Ride: AU2 Ute

Location: melbourne
VIC, Australia

You can buy kits with a carby plate. They sit under the carby and work in the same way. The nitrous and fuel come from the plate which is fed from the solonoids.
Top
 Profile  
 
 
Posted: Wed Jul 27, 2005 12:44 pm 
Getting Side Ways
Offline
User avatar

Posts: 1960

Joined: 6th Nov 2004

Gallery: 22 images

Power: 315 rwkw

Location: Under the flight path of incoming packpackers
NSW, Australia

Yeah NOS is big time old school... they were adding it to big carbys back befor most of us were born
Top
 Profile  
 
 
Posted: Thu Jul 28, 2005 1:38 am 
Smokin em up
Offline
User avatar

Age: 39

Posts: 297

Joined: 5th Nov 2004

Ride: 410 Cube FE LTD

Location: Canberra
ACT, Australia

cool, i was going to set my 400 up to either me turboed/ supercharged but i think my compression will be way to hight like 10.5:1 and i think n20 will complement it better
Top
 Profile  
 
 
Posted: Fri Jul 29, 2005 8:36 pm 
Getting Side Ways
Offline
User avatar

Age: 37

Posts: 593

Joined: 5th Nov 2004

Gallery: 13 images

Location: Melbourne
VIC, Australia

go to VPW and check out what they have for carbys, you might find something.

http://www.vpw.com.au/category.asp?CatI ... rCatID=372

 

_________________

4 cylinders are like chinese food, few minutes after you have them you just want more!

Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 2 of 2  [ 29 posts ]  Go to page Previous  1, 2

Who is online

Users browsing this forum: No registered users and 13 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Sat Nov 23, 2024 8:47 pm All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names