|
xr6digga |
|
||
|
just installed a new unifilter into my EF2 XR6. On replacing this I noticed on the inside of the airbox cover there was a tube which ran almost the length of the cover. Is this necessary or can i hacksaw it off so the air can run directly into the engine?
|
||
Top | |
eagleaus |
|
||
|
Leave in, it draws the air from the centre rather then the end of the box.
|
||
Top | |
Slick |
|
|||
|
xr6digga wrote: just installed a new unifilter into my EF2 XR6. On replacing this I noticed on the inside of the airbox cover there was a tube which ran almost the length of the cover. Is this necessary or can i hacksaw it off so the air can run directly into the engine? yeah dude, I service my wifes EF panel unifilter couple of months back after 5400K's. notice a concentrated thick black round circle in the centre of the filter, put it up against the sun light & you can't see throu it.
I compared it with the utes filter{unifilter} which was spread out evenly. still see alot of sun light throu it, EL & AU sucks air from all 4 corner of the filter. I ended up hacking it off. ended up with a 80mm opening.
_________________ Mind f**k!!! it works on feeble minded ignorant sheeples... there's plenty of em on this site... some are very intelligent but by god they are so thick!!! Pakrat wrote: You can buy them seppertly
|
|||
Top | |
uglybob |
|
|||
|
the EF airbox lid was flow-tested as the best out of the EF/EL/AU lids, due to the trumpet inside of the lid.
so remove if you wish, it won't make sweet FA of a difference!
_________________ R.I.P. Scotty |
|||
Top | |
Slick |
|
|||
|
uglybob wrote: the EF airbox lid was flow-tested as the best out of the EF/EL/AU lids, due to the trumpet inside of the lid. but if you remove the trumpet & mount a inbox pod filter & 80mm adapter will that make sweet FA of a difference?
so remove if you wish, it won't make sweet FA of a difference! All I can say is it has a better throttle response, less service on the EF filter.
_________________ Mind f**k!!! it works on feeble minded ignorant sheeples... there's plenty of em on this site... some are very intelligent but by god they are so thick!!! Pakrat wrote: You can buy them seppertly
|
|||
Top | |
uglybob |
|
|||
|
again, pods have been proven to show next to no real difference over panel ones.
each to their own - if you want to cut it off, go for it - but either way its not going to really change much power-wise!
_________________ R.I.P. Scotty |
|||
Top | |
Slick |
|
|||
|
uglybob wrote: again, pods have been proven to show next to no real difference over panel ones. good think I didn't purchase one of those fancy 3" mendral bent intake pipes & pod filters. hehehe
each to their own - if you want to cut it off, go for it - but either way its not going to really change much power-wise! all those test was done on stock lids. EF with 55mm tube opening or bell mouth. against 55mm ventury opening of au's side of box. but did they test a 80mm bell mouth adapter for comparision?
_________________ Mind f**k!!! it works on feeble minded ignorant sheeples... there's plenty of em on this site... some are very intelligent but by god they are so thick!!! Pakrat wrote: You can buy them seppertly
|
|||
Top | |
xr6digga |
|
||
|
thanks for your replies guys.
seems like it it best to keep the trumpet in there as removing it is just a s**t of a job with no real enhancement to the running of the car. |
||
Top | |
Slick |
|
|||
|
xr6digga wrote: thanks for your replies guys. leave it as is unless you have some major mods eg: blueprinted, full engine balance, lighten flywheel & driveshaft, big cam, extensive head work, injectors, extractors, exhaust & aftermarket ECU.
seems like it it best to keep the trumpet in there as removing it is just a s**t of a job with no real enhancement to the running of the car.
_________________ Mind f**k!!! it works on feeble minded ignorant sheeples... there's plenty of em on this site... some are very intelligent but by god they are so thick!!! Pakrat wrote: You can buy them seppertly
|
|||
Top | |
Who is online |
---|
Users browsing this forum: Google Adsense [Bot] and 66 guests |