|
| Happy |
|
|||
|
{USERNAME} wrote: gaz stainless u need a TIG welder
crap - you can get gassless wire for welding stainless with a MIG
_________________ Owning 1 of 67612 EF GLi Sedans made
|
|||
| Top | |
|||
| Disco Frank |
|
|||
|
{USERNAME} wrote: {USERNAME} wrote: gaz stainless u need a TIG welder crap - you can get gassless wire for welding stainless with a MIG well yes... but a tig will work best 
_________________ RIP SCOTT |
|||
| Top | |
|||
| madmax |
|
|||
|
{USERNAME} wrote: {USERNAME} wrote: {USERNAME} wrote: gaz stainless u need a TIG welder crap - you can get gassless wire for welding stainless with a MIG well yes... but a tig will work best Maybe, but it is possible to weld stainless with an arc. The guys do it at work all the time. Migs & Tigs are almost non-existant.
_________________
|
|||
| Top | |
|||
| Gaz |
|
||
|
yeh, we got an arc, just gotta get me hands on some stainless steal welding rods.. damn expensive things!
sorry to hi-jack ur thread timmeh.. but here is a sneak peak at the exhaust tip.. twin 2" into 2.5" pipe, just gotta be welded togeather, and cut down to the right size. 
_________________ 2007 Steel BF Ghia MKII V8 - 19" GTP's + Superlows |
||
| Top | |
||
| Timmeh |
|
||
|
Damn you hijacker Gaz!!!!
Here is the dash slightly forward. Have to undo s**t of plugs and undo some of the dodgy wiring done by Kurt. HAHHAHAHAHA. Only cut 1 wire which in the end I didnt need to. 
Here it is again from a different angle just prior to me pulling it out. 
Here is the dash out. 
Still yet to remove pedal box. I hope its not a C***. |
||
| Top | |
||
| Happy |
|
|||
|
may as well do the CC updated while you are at it mate!!! You're half way there!!!
_________________ Owning 1 of 67612 EF GLi Sedans made
|
|||
| Top | |
|||
| Timmeh |
|
||
|
Stuff climate control. I dont muck around with it too much. Full cold or full hot is what I use.
Happy it can be done with one person. |
||
| Top | |
||
| Timmeh |
|
||
|
This is what it came down to.
Crappy little spot welds. Going to be a beast when I get it fixed and reinforced. 
|
||
| Top | |
||
| nico95 |
|
||
|
hey. mines just shat itself as well. is there a way at all you get a mig welder up there? without having to take the dash out? or would it be to dangerous with the sparks coming off?
|
||
| Top | |
||
| Timmeh |
|
||
|
Dangerous with the sparks and s**t. Plus if it has bent as well then you need some force to close the gap before welding.
Take it out and while its out get someone to reinforce it and make it tougher so that if you want a heavier clutch in it it wont break again. Hey your in Warwick. If you need a hand while my memory is fresh give us a PM. |
||
| Top | |
||
| nico95 |
|
||
|
cheers mate. will do. most likely will get started on it tomorrow. will let you no how im goin 4 sure. thanks.
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 18 guests |
