|
| eed-250 |
|
||
|
After about 500kms since Scotty (RIP) put my cam in, the motor has been really loud. Rattling its tits off at anything over 1000rpm.
Is it my lifters? Did scott(rip) shim it wrong?? What parts do i need to replace so i can stop this noise. makes the car sound liek s**t.. thanks guys.. |
||
| Top | |
||
| Andrew J |
|
|||
|
Could be your lifters, might be something else. My cars making some really bad sounds :S Sounds rattly at idle, and makes a sort of sloshing noise... Not good. Might be time to get myself a cam and start doing the lifters etc while its going in.
_________________ The problem with America is stupidity. I'm not saying there should be a capital punishment for stupidity, but why don't we just take the safety labels off of everything and let the problem solve itself?
|
|||
| Top | |
|||
| Disco Frank |
|
|||
|
doubt he would of shimed it wrong
btw 9months 
most prolly the lifters are gone.. strange it above 1000rpm as usally it low oil pressure at idle that cause them to rattle.. mm might have a exhuast leak?
_________________ RIP SCOTT |
|||
| Top | |
|||
| altedxr6 |
|
|||
|
check your timing chain guides, they need to come loose a bit to do a cam swap sometimes, maybe scott(rip) did not retension them up right? ... (im sure he would of though) Someone bought a cam from me, installed it, and got the rattling sound.
Found it was the timing chain guide tensoner that sits underneath the power steering up was not tight enough . cheers, hope that heaps. |
|||
| Top | |
|||
| Slick |
|
|||
|
I find the same problem with the wifes EF, only happens during start up when parked in a steep area. I guess the grankshaft is submerge where the oil level is at its highest, sloshing.
_________________ Mind f**k!!! it works on feeble minded ignorant sheeples... there's plenty of em on this site... some are very intelligent but by god they are so thick!!! Pakrat wrote: You can buy them seppertly
|
|||
| Top | |
|||
| mreb |
|
|||
|
theres another thead on that mine makes a sloosh noise the other bloke found the converter it the auto had a broken vain ,thats if you got a auto if not dont listen to me.its only when the front is raised .and usally most rattles are timing chain or guides i just replaced mine all good now
|
|||
| Top | |
|||
| Slick |
|
|||
|
mreb wrote: theres another thead on that mine makes a sloosh noise the other bloke found the converter it the auto had a broken vain ,thats if you got a auto if not dont listen to me.its only when the front is raised .and usally most rattles are timing chain or guides i just replaced mine all good now That might be it. in my case I hope the broken vain is jammed in tight somewhere in the convertor housing.
thanks for that.
_________________ Mind f**k!!! it works on feeble minded ignorant sheeples... there's plenty of em on this site... some are very intelligent but by god they are so thick!!! Pakrat wrote: You can buy them seppertly
|
|||
| Top | |
|||
| mreb |
|
|||
|
i hope so to im not changing it until it stops moveing
|
|||
| Top | |
|||
| rushed |
|
|||
|
yeah mine does the same thing when i start on a hill, it does it all the time on my driveway. start and try to go up hill , into the garage and the thing stalls or really tries to.
so you guys think it could be the auto's converter, i needed an excuse to get a high-stall. lol |
|||
| Top | |
|||
| eed-250 |
|
||
|
Frank, he had about 4 beers during the install.. haha i wasnt complaining coz he did it for free
ah k. could be the tensioner then, but everyone is saying its the lifters.. thanks for the tip dude. |
||
| Top | |
||
| Disco Frank |
|
|||
|
eed-250 wrote: Frank, he had about 4 beers during the install.. haha i wasnt complaining coz he did it for free
ah k. could be the tensioner then, but everyone is saying its the lifters.. thanks for the tip dude. fakr 4 beers for scott he would have been maggot!!! IF he put the shims in it would have been right
_________________ RIP SCOTT |
|||
| Top | |
|||
| Slick |
|
|||
|
mreb wrote: i hope so to im not changing it until it stops moveing like rushed said! that will give me a good excuse to install a higher torque converter in the au ute instead of the wifes EF.
thanks for that 
_________________ Mind f**k!!! it works on feeble minded ignorant sheeples... there's plenty of em on this site... some are very intelligent but by god they are so thick!!! Pakrat wrote: You can buy them seppertly
|
|||
| Top | |
|||
| XR6EB |
|
||
|
Do you know what cam it is?
I recently had my engine builder try to find a rattling noise that my engine was making [6 months old], and after 2 weeks of replacing lifters and timing chain guides, he gave my cam supplier a call to find out that the sound is caused by "backlash on the cam" and is meant to be their. This type of cam is commenly used by fordmod members.
_________________ EB S XR6
|
||
| Top | |
||
| eed-250 |
|
||
|
its a wade 1004@112.
:S |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 75 guests |
