|
| GTFORDMAN |
|
|||
Age: 44 Posts: 1475 Joined: 5th Nov 2004 Ride: 98 EL Falcon - Last of the EL's Location: Muswellbrook |
i have a little problem i hope some one can help me with, my car, according to the gauge has high oil pressure, now being a newly rebuilt engine and only done about 1.5K's arfter being rebuilt would i need to pull my engine back down again (please god NOOOOO) or am i worried about nothing.
any help would be great.
_________________ why are women like clouds? eventually they f**k off and its a really nice day.
|
|||
| Top | |
|||
| LTDHO |
|
|||
|
High Oil press is very good. Is it still registering on the gauge?
|
|||
| Top | |
|||
| GTFORDMAN |
|
|||
Age: 44 Posts: 1475 Joined: 5th Nov 2004 Ride: 98 EL Falcon - Last of the EL's Location: Muswellbrook |
Yes, only just, at idle it sits between the second last marker and the last marker on the gauge, but when you rev it a bit, it goes past the last marker (a little bit).
um can you tell me why High oil pessure is good?, i always heard its not so good.
_________________ why are women like clouds? eventually they f**k off and its a really nice day.
|
|||
| Top | |
|||
| NC 5ltr |
|
|||
|
i think low pressure means that the engine has some major problems like somethin aint workin or your oil level is low.
dont qoute me on it though 
_________________ "Looking at cleavage is like looking at the sun. You don't stare at it. It's too risky. You get a sense of it and then you look away."
|
|||
| Top | |
|||
| xdv8 |
|
||
|
both extremes are bad, low usually means excessive bearing gaps, high pressure could mean there is a blockage in one of the galleries, before jumping to conclusions, get your sender unit and gauge checked
|
||
| Top | |
||
| Andrew J |
|
|||
|
{USERNAME} wrote: both extremes are bad, low usually means excessive bearing gaps, high pressure could mean there is a blockage in one of the galleries, before jumping to conclusions, get your sender unit and gauge checked
Hate to burst your bubble, but theres a fair chance its not gauges. Its still a good idea to check them, but after rebuilding an engine, it would seem suspicious that they went at the same time. But you never can be too careful 
_________________ The problem with America is stupidity. I'm not saying there should be a capital punishment for stupidity, but why don't we just take the safety labels off of everything and let the problem solve itself?
|
|||
| Top | |
|||
| EBXR8380 |
|
|||
|
Did they pack the oil return spring ?
Or fit a high presure / volume pump? Check with capilary gauge? It maybe 10 higher than normal, with electronic gauge it maybe alittle out of calibration ????Reading higher than it should...
_________________ As in ZOOM 126 edition Last edited by EBXR8380 on Mon Dec 06, 2004 10:55 pm, edited 1 time in total. |
|||
| Top | |
|||
| GTFORDMAN |
|
|||
Age: 44 Posts: 1475 Joined: 5th Nov 2004 Ride: 98 EL Falcon - Last of the EL's Location: Muswellbrook |
{USERNAME} wrote: Did they pack the oil return spring ?
Or fit a high presure / volum pump? the Mods i did to my engine when i rebuilt it were,crank reground, the block decked 10thou, stg2 heads (unleaded), stg2 cam, bigger carb, more agressive coil. i left the oil pump as it was when it came out - standard, but i will now have my gauges checked - just to be safe.
_________________ why are women like clouds? eventually they f**k off and its a really nice day.
|
|||
| Top | |
|||
| pinkbits8u |
|
|||
|
put a mechanical gauge on it close to the donk and what pressure is it at idle and at revs when warm
my old clevo had 95 psi and it ran for 7 years and umpteen hundred thousand ks with high oil pressure with no trouble what grade oil are you using . |
|||
| Top | |
|||
| EBXR8380 |
|
|||
|
Hmm sounds like tight clearances??
I'd run a low visc oil !!! Like 5/30... to get good even lubrication....
_________________ As in ZOOM 126 edition |
|||
| Top | |
|||
| GTFORDMAN |
|
|||
Age: 44 Posts: 1475 Joined: 5th Nov 2004 Ride: 98 EL Falcon - Last of the EL's Location: Muswellbrook |
{USERNAME} wrote: put a mechanical gauge on it close to the donk and what pressure is it at idle and at revs when warm
my old clevo had 95 psi and it ran for 7 years and umpteen hundred thousand ks with high oil pressure with no trouble what grade oil are you using . the grade of oil is, 10/40, i was worried about it being a little thin, & for some reason i can no longer find 20/40.
_________________ why are women like clouds? eventually they f**k off and its a really nice day.
|
|||
| Top | |
|||
| AXR88U |
|
|||
|
Maybe the sender unit is rooted
_________________ ________________________________________
|
|||
| Top | |
|||
| AXR88U |
|
|||
|
Only real problem with too much pressure is that your soaking up a little power to drive the pump.
_________________ ________________________________________
|
|||
| Top | |
|||
| AXR88U |
|
|||
|
Maybe you need to use a softer bypass spring in the pump.
_________________ ________________________________________
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 47 guests |
