|
znipa-x |
|
|||
|
{USERNAME} wrote: was talking to my mate about this on the weekend, and he suggested to have the elgt snorkel, but then also have a 3" flexi pipe coming fom air box and take it down the bottom of engine bay and stick it out under front bar, or there abouts....
is this a good idea?? just not sure how it would go with having 2 inputs... I had this, but didn't have the snorkel, just had some airseeder hose plumbed down through the plastic guard at the bottom and into the airflow under the bumper, this created a postive pressure in the airbox more than the stock snorkel did, used a manometer ( tupbe with water in it) to prove the fact. gone away from it now for a bigger snorkel as the hose perished and it also increased the ingestion of bugs into the airbox, also ended up with some water in there are hitting a rather deep puddle.
_________________ former FORD V8 owner
|
|||
Top | |
Bsjenko |
|
|||
|
{USERNAME} wrote: {USERNAME} wrote: was talking to my mate about this on the weekend, and he suggested to have the elgt snorkel, but then also have a 3" flexi pipe coming fom air box and take it down the bottom of engine bay and stick it out under front bar, or there abouts.... is this a good idea?? just not sure how it would go with having 2 inputs... I had this, but didn't have the snorkel, just had some airseeder hose plumbed down through the plastic guard at the bottom and into the airflow under the bumper, this created a postive pressure in the airbox more than the stock snorkel did, used a manometer ( tupbe with water in it) to prove the fact. gone away from it now for a bigger snorkel as the hose perished and it also increased the ingestion of bugs into the airbox, also ended up with some water in there are hitting a rather deep puddle. valid point bout the bugs and water.... didnt even click with me about that.. i might just stick with the elgt snorkel i think. saves the bugs, water, and the hose perishing... cheers people... very goodly,
_________________ The Lane Lives.... Finally!!!! |
|||
Top | |
veeate |
|
|||
|
a pod filter is only good if you make a seperate enclosure for it keeping the hot air out (similiar to the way the standard air box works....most people just chuck a pod under the bonnet and this is no good as the engine is sucking hot air from under the engine bay instead of cold air from outside..i have a K&N panel filter with an EL intake and i reckon its better than a pod filter...i put an extra inlet goin to the airbox and i knocked off 2 tenths of a second down the 1/4 mile...
|
|||
Top | |
Ben_Daui |
|
|||
|
{USERNAME} wrote: The AU snorkle won't fit ont the V8's due tot he power steering pulley. You can get around it by heating hte snorkle up and bending it slightly giving it enough clearance. Otherwise the EL GT/XR8 snorkle will fit straight on and flows more than enough for 99% of 5L's out there.
Well the AU XR8 snorkle will go on but not in the standard screw holes! First place the snorkle on the air box , then twist the snorkle untill it doest hit the power steering pulley then get someone to hold the snorkle in place until you have lined up & marked out new screw holes & then screw the bastard into place. I know it does fit in as I have seen it on a few E-series V8's & as Rob(yobbo4d) had it on his old v8. Cost of snorkle $30 from SINCLAIR FORD my local FORD DEALER!
_________________ MEMBER 1390 |
|||
Top | |
EDXR8 |
|
|||
|
{USERNAME} wrote: Well the AU XR8 snorkle will go on but not in the standard screw holes!
First place the snorkle on the air box , then twist the snorkle untill it doest hit the power steering pulley then get someone to hold the snorkle in place until you have lined up & marked out new screw holes & then screw the bastard into place. Yeah thats an option but you may have problems doing that if you have thermos, they may stop you from rotating the snorkle. I know people get away with it by cutting the thermo shroud to allow a bit more clearance. |
|||
Top | |
TS50EB |
|
|||||
|
I fitted an AU3 XR8 Ticky snorkel to my EB (Thermo's and V8). I just needed to make an adapter to reach the rad support, see the attached pic.
_________________ The car should be called "Frankenstien". EBII GLi skeleton, AU T2 220kw heart, AU2 brain, EF/EL for everything else. |
|||||
Top | |
Bsjenko |
|
|||
|
just a supid question.... i went to auto parts place today to get a pod filter, thinking i would just have to say what car it was and they woud have the filters marked what models they are for. but... they only get marked as a diameter.
so what diameter pod should i be getting, and also is there a plate or something that actually holds the filter into place?? it prob sounds dumb, but i have never done this before, and most of my mates dont mod there cars.. cheers
_________________ The Lane Lives.... Finally!!!! |
|||
Top | |
EDXR8 |
|
|||
|
A pod filter will probably cost you power unless you do a lot of work modifying the factory box or fabricating a custom one. Just get yourself a decent panel filter and snorkle.
|
|||
Top | |
Who is online |
---|
Users browsing this forum: No registered users and 46 guests |