|
master_jawa |
|
||
|
Has anyone had any experience with aftermarket alloy heads for cleveland engines? anyone got Pro's & Con's, especially with a stroker setup?
|
||
Top | |
xr8ute |
|
||
|
Theres a couple of blokes running CHI-headed Cleveland strokers on fordforums.com.au, in the Cleveland section (of course)
|
||
Top | |
paulhowes |
|
|||
|
Anyone that builds a serious clevo goes the aluminium. They are lighter have less hot spots and better heat dispersion and there are heaps available that will give you just as good a result as 4V's. CFord Motorsport have a few on their website like C302 and C302B (as used by ben gatt) which are high port gems but require custom exhaust. and yella terra and a host of others. Edelbrock do one that takes large valves avail. bare at rocketind. You will have less detonation problems with alloys if you are running high comp but personal choice, can you justify the cost.
Here's an example take a look here. http://www.pavtek.com.au/pp_3vheads.html The flow at their nominated lift is a bit unrealistic for a streeter but there is a flow chart at the bottom of page about 500 thou is a good all round lift that wont be too much drama on a good valve train. |
|||
Top | |
tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
it comes down to cost. if you just want a warm streeter use stock iron 2V heads.
if you are thinking of spending alot on porting don't and get some alloy heads most of them have better flow out of the box. and like has been said they fix alot of the problems the stock iron heads |
||
Top | |
twr7cx |
|
|||
|
is there any disadvantage in the long run about using two different metals? iron block and alloy heads would have different heat rates and that. if your not really building then engine for power, but more a nice long lasting cruiser, would a safer bet be to stay with the iron heads?
|
|||
Top | |
tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
{USERNAME} wrote: is there any disadvantage in the long run about using two different metals? iron block and alloy heads would have different heat rates and that. if your not really building then engine for power, but more a nice long lasting cruiser, would a safer bet be to stay with the iron heads?
remember what your 6cyl engine and head are made from |
||
Top | |
twr7cx |
|
|||
|
{USERNAME} wrote: {USERNAME} wrote: is there any disadvantage in the long run about using two different metals? iron block and alloy heads would have different heat rates and that. if your not really building then engine for power, but more a nice long lasting cruiser, would a safer bet be to stay with the iron heads? remember what your 6cyl engine and head are made from BINGO! My point exactly (now I'm not saying that this is due to the iron block and alloy head as I don't know the actual reasoning), but how many people with I6's blow headgaskets pretty bad? |
|||
Top | |
iam death |
|
|||
|
i gotta ask with a name like jawa are you into formula 500 or speedway altogether????????
_________________ 'WALKER f**k MY WIFE AND ALL I GOT WAS THIS s**t SIGGIE' |
|||
Top | |
EBXR8380 |
|
|||
|
{USERNAME} wrote: {USERNAME} wrote: {USERNAME} wrote: is there any disadvantage in the long run about using two different metals? iron block and alloy heads would have different heat rates and that. if your not really building then engine for power, but more a nice long lasting cruiser, would a safer bet be to stay with the iron heads? remember what your 6cyl engine and head are made from BINGO! My point exactly (now I'm not saying that this is due to the iron block and alloy head as I don't know the actual reasoning), but how many people with I6's blow headgaskets pretty bad? Yes there are issues, but in most cases its due to crap cylinder head bolts that loose there elasticity..Even then they did 100.000 before they blew..On high power engines its quite often an issue with heads lifting due to weak head bolts. Thats why all good hi po engines use studs to pull there heads down..
_________________ As in ZOOM 126 edition |
|||
Top | |
383xd |
|
||
|
I am in the same postion in that I am looking at putting alloy heads on my cleavo one day and still not sure where to get them from, as mentioned there are the CHI heads and the other heads I am looking at are from AFD
http://www.airflowdynamics.com.au/
_________________ No subsitute for cubic inches |
||
Top | |
tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
{USERNAME} wrote: {USERNAME} wrote: {USERNAME} wrote: is there any disadvantage in the long run about using two different metals? iron block and alloy heads would have different heat rates and that. if your not really building then engine for power, but more a nice long lasting cruiser, would a safer bet be to stay with the iron heads? remember what your 6cyl engine and head are made from BINGO! My point exactly (now I'm not saying that this is due to the iron block and alloy head as I don't know the actual reasoning), but how many people with I6's blow headgaskets pretty bad? the dissimilar metals is only a small part of the head gasket thing with the 6cyls. there are a number of other factors aswell. personly i dont see the head gasket as a big thing to be concerned over. lets face it by the time they blow most of valves are not sealing properly any more and the ports and valves are covered in carbon build up. having to take the head off is forcing you to fix these problems and give yourslef better fuel economy. |
||
Top | |
Rapier |
|
||
|
plus the size of the heads is a problem as well a 4.0L i6 head is massive
|
||
Top | |
Who is online |
---|
Users browsing this forum: No registered users and 44 guests |