|
| spannerhead |
|
|||
|
Any hints on how to remove those last bits of gasket on a surface without scraping with a screwdriver?
_________________ Thorpy says single wipers are Fully SIK!
|
|||
| Top | |
|||
| Andrew J |
|
|||
|
Use a paint scraper, or something ridiculously sharp! The trick is not to go too deep, and dont touch the housing itself. It needs to be flat and level, but residue from the gasket should be fine. Some solvents may also help to soften the gasket, maybe eucalyptus oil or something, and then you could rub it off with a finger nail. Just go slowly and take care.
_________________ The problem with America is stupidity. I'm not saying there should be a capital punishment for stupidity, but why don't we just take the safety labels off of everything and let the problem solve itself?
|
|||
| Top | |
|||
| Gaz |
|
||
|
our freezer came with a paint scraper.. only it was made of plastic, that would probably do a good job?
_________________ 2007 Steel BF Ghia MKII V8 - 19" GTP's + Superlows |
||
| Top | |
||
| Rapier |
|
||
|
wire brush on an angle grinder or drill does a good job, dont use it on alloy though
|
||
| Top | |
||
| Concord |
|
||
|
a single sided razer blade will do the trick.
|
||
| Top | |
||
| twr7cx |
|
|||
|
i used a big paint scraper. wire brush on a drill or grinder sounded far too rough fior my liking!
|
|||
| Top | |
|||
| Rapier |
|
||
|
i dont see how a wire brush is ever gonna hurt a cast iron block!
|
||
| Top | |
||
| Krytox |
|
|||
|
just my input,
NEVER use a wire attachment on a drill or a angle grinder on a cast iron block, this will rounden the oil galleries and water jacket holes and any other hole. think about it... even if its a ticks d**k rounder fluid will have more of a chance to get under the gasket. many people use wire brushes and have no problems, be my guest. pay me out all you want but... my suggestion is CRC gasket stripper and a nice sharp steel scraper. PS: we are talking about a head gasket arent we? there are many gaskets! Thank-Ya
_________________ Carefree, we may not be number one, but we're up there. |
|||
| Top | |
|||
| kempster1 |
|
|||
|
The best gasket scrapers are cheap wood chisels.
Then do the final clean up with a scotchbrite pad, buy the good ones not the cheap ones.
_________________ Peter Kempster |
|||
| Top | |
|||
| madmax |
|
|||
|
Krytox wrote: just my input,
NEVER use a wire attachment on a drill or a angle grinder on a cast iron block, this will rounden the oil galleries and water jacket holes and any other hole. think about it... even if its a ticks d**k rounder fluid will have more of a chance to get under the gasket. many people use wire brushes and have no problems, be my guest. pay me out all you want but... my suggestion is CRC gasket stripper and a nice sharp steel scraper. PS: we are talking about a head gasket arent we? there are many gaskets! Thank-Ya I see your point. However I have aways used a very fine wire brush on cast iron not a course one that may damage the any of the holes. On alloy I always use a scraper only.
_________________
|
|||
| Top | |
|||
| stiddy |
|
||
|
i used a hand held wire brush, and diesel, if that dosent work usually try a sharp scraper or the dremil with one of the sanding attachments.. never had any dramas..
_________________ I desperately want to be a road statistic |
||
| Top | |
||
| 4.9 EF Futura |
|
|||
|
Krytox wrote: pay me out all you want but... my suggestion is CRC gasket stripper and a nice sharp steel scraper.
I'll second this notion. CRC gasket stripper is gold in a can, should make the scraping process easy, with a little patience....
_________________ I promise..... I will never die. |
|||
| Top | |
|||
| EBXR8380 |
|
|||
|
[quote="Krytox"]just my input,
NEVER use a wire attachment on a drill or a angle grinder on a cast iron block, this will rounden the oil galleries and water jacket holes and any other hole. think about it... even if its a ticks d**k rounder fluid will have more of a chance to get under the gasket. many people use wire brushes and have no problems, be my guest. pay me out all you want but... my suggestion is CRC gasket stripper and a nice sharp steel scraper. PS: we are talking about a head gasket arent we? there are many gaskets! ============================================== Nearly all automotive shops I have been to over the years use wire brush..Done carefully it would be o/k.. All presure faces should be re- faced any way...Like heads and block decks [if engine is out] I use a sharpened broken steel cutting blade.. Like a big hacksaw blade.. Some common sense though some emery paper can be used but DON'T let abrasive material into engine and DON'T grind the crap out of one area...
_________________ As in ZOOM 126 edition Last edited by EBXR8380 on Mon Feb 06, 2006 11:53 am, edited 1 time in total. |
|||
| Top | |
|||
| EBXR8380 |
|
|||
|
Gremlin..Double post...
_________________ As in ZOOM 126 edition |
|||
| Top | |
|||
| dynomite!!!! |
|
||
|
if it is a head gasket and your cleaning the block follow what EBXR8380 said crc gasket stripper is very effective but dont get it on your skin it burns. if you are trying to do the head take it to a head rebuilder and get it milled (alloy head) or plained (cast iron head) if this is not done you run a risk of your head gasket leaking, which would make replacing the gasket pointless. A head rebuilder will acid dip the head and clean it entirely and does'nt cost stuff all
_________________ I caught you a delicious bass |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 68 guests |
