|
| Evil Au tonner |
|
|||
|
on you LPG tank they have a sender unit that send the signal to the LPG Gauge it sounds like your sender unit is died in the a** easy way to see if that is it you disconnect the earth wire of the sender unit on the tank and earth it out you gauge should read full if not its the gauge itself ( or its the other way round lol its late)
_________________ To be old and wise you first have to be young and stupid |
|||
| Top | |
|||
| Evil Au tonner |
|
|||
|
just get the heat shield and start bending to fit
_________________ To be old and wise you first have to be young and stupid |
|||
| Top | |
|||
| bennzy |
|
||
|
yeah, i mite take it to the gas place cause that was the one of the things they were going to check when i had my car in for a service, but they didnt have time to do it so hopefully this week ill have time to take it to him so he can have a look at it better, just hope i can make it read better was working at better a fair while ago
|
||
| Top | |
||
| bennzy |
|
||
|
from memory i was told with my gas conversion on my ef ghia that i will have to move the unit that is near the extractors to fit properly without any problem
|
||
| Top | |
||
| Evil Au tonner |
|
|||
|
your convertor is it massive?
_________________ To be old and wise you first have to be young and stupid |
|||
| Top | |
|||
| Evil Au tonner |
|
|||
|
the unit that should be on the strut tower
_________________ To be old and wise you first have to be young and stupid |
|||
| Top | |
|||
| bennzy |
|
||
|
ummm cant remember it doesnt look really big, tomorrow ill take a pic of it and paste it in here to show u, but i think its more because its sticking out and with the bracket thats holding it
|
||
| Top | |
||
| bennzy |
|
||
|
yeah thats the one i was talking about on the strut tower
|
||
| Top | |
||
| Evil Au tonner |
|
|||
|
my convertor is massive all i did was modify my heat shield to sit over the headers and made a custom heat shield to sit around the convertor to save the wiring and pluming. There is still some clearence between the convertor and headers
_________________ To be old and wise you first have to be young and stupid |
|||
| Top | |
|||
| bennzy |
|
||
|
oh ok, kool well yeah i check it out tomorrow anyway, but i dont think ill be able to put comp ones in tho which is something i want, but even if its not comp its still good enough, will also call in to the exhaust place that work uses and see wat he says again
|
||
| Top | |
||
| Evil Au tonner |
|
|||
|
asked my boss about the climate control stuffing up your gauge he said to check your connections
_________________ To be old and wise you first have to be young and stupid |
|||
| Top | |
|||
| bennzy |
|
||
|
kool, think it mite be a connection also since i went to an exhaust place and he said for that much fuel loss it cant be a exhaust problem, but he also said that i cant fit pacemaker comps on the middle range ones because of the bracket thats on the strut thats holding the thing in, i mite just get the basic comp ones in but still not alot of room, i pretty much have to get a new bracket it or i have to edit the bracket but for $570 he said roughly will cost me that much to supply and fit with all the s**t he needs to do, that is pretty much the best pacies i can get if i go further i will need to change computer components etc...
|
||
| Top | |
||
| Evil Au tonner |
|
|||
|
Sweet as thats pretty good i recon
_________________ To be old and wise you first have to be young and stupid |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 80 guests |
