|
| FTR-XR6 |
|
|||
|
Hi guys,
I know this is a pretty open ended question, but how hard would it be to put fairmont trims in and connect up electric windows to my rear windows? Whats involved? Just wondering whether to give it a try or just give it up now before I start...
_________________
|
|||
| Top | |
|||
| uglybob |
|
|||
|
do it! new body loom (fairmont), real electric regulators, rear (full) door trims, 4 panel switch. we got it done in a few hours easy-as
_________________ R.I.P. Scotty |
|||
| Top | |
|||
| snap0964 |
|
|||
|
I'm assuming your referring to an EL XR6 - actually it should be easier - you should only need to replace the rear door looms to the plug inside the lower body pillars - pull the grommet below the rear door hinges to access. Alternatively, add the 3 wires from there into the rear doors through the conduit. Read http://www.fordmods.com/forums/viewtopi ... ight=rivet for advice on mounts for the rear door handles.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| FTR-XR6 |
|
|||
|
Yeh...it's for an EL XR6
So all i need is rear door trims, 2 window regs and the rear door looms which will plug straight into the plug in the b pillar? So there's no need for joining wiring or any s**t like that....I'd be lost with anything like that. I also dont want to have control of the rear windows in the front....quite happy to just have the buttons on the rear doors only. P.S. Thanks for the link snap, but it really didn't help much. Thanks guys...I guess if I go ahead with it I know to hit you up for any help I need bob 
_________________
|
|||
| Top | |
|||
| snap0964 |
|
|||
|
FTR-XR6 wrote: So all i need is rear door trims, 2 window regs and the rear door looms which will plug straight into the plug in the b pillar? So there's no need for joining wiring or any s**t like that....I'd be lost with anything like that. I also dont want to have control of the rear windows in the front....quite happy to just have the buttons on the rear doors only. The 4 switch panel would be handy, but you can do some wiring mods to make do with the 2.FTR-XR6 wrote: P.S. Thanks for the link snap, but it really didn't help much. No probs - wait til you go to put the rear trims with the arm rests and handles on - then read that thread again.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| uglybob |
|
|||
|
happy to lend a hand!
_________________ R.I.P. Scotty |
|||
| Top | |
|||
| FTR-XR6 |
|
|||
|
bob, did you use the 4 switch panel in the front? The pic in your gallery shows only the two...
_________________
|
|||
| Top | |
|||
| uglybob |
|
|||
|
pic is a very old one - you can't use the 2 one, needs to be the 4-panel
_________________ R.I.P. Scotty |
|||
| Top | |
|||
| FTR-XR6 |
|
|||
|
Damn, didn't want to have the full control panel at the front, maybe I'll leave it then... my electrics knowledge is nil
_________________
|
|||
| Top | |
|||
| uglybob |
|
|||
|
haha mine is too, but its all plug & play!
you don't need to 're-wire' anything as such, it all swaps over
_________________ R.I.P. Scotty |
|||
| Top | |
|||
| BOSXR8 |
|
|||
|
i did this last weekend for a gli, it was alot of work to take the interior and all that s**t out but i got it all don in one day, mind you i had to cut my loom from the point where it goes into the boot and re solder all the wires, and i also had a relay switch in the loom near where it connects at the drivers footwell.. hmmm anway im sure you will be fine with it shoudlnt take you long at all if u dont even have to change the body loom!
_________________ EB SXR6. ED XR8 Sprint. |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 72 guests |
