|
| rizzo |
|
||
|
small question regarding the installation of a air fuel ratio gauge in a EBII S XR6. has anyone connected one up? if so which wire do i splice into on the oxy sensor as there is 2 white wires and 1 black wire?
can anyone help me out with which wire is the correct wire to use?
_________________ If it moves, weld it down! |
||
| Top | |
||
| ebs_4l |
|
||
|
i wouldnt waste my time hooking one up to a std o2 sensor, you need a full wideband a/f ratio meter to use it properly... a std sensor basically has a on/off output, all it can tell you is whether you are above or below 14.7:1 (thats simplified but about as good a signal as they have)
and since you will be running in closed loop for probably most of the time, the gauge will just be showing a continous rich/lean/rich/lean/rich/lean. with a wideband setup, like the innovate LM-1, the output from the meter is directly proportional to a/f ratio!!! an is about as accurate as they come
_________________ EB 4L, 8.4:1, R154, GT4202r, 4in exhaust, Greenslade Engineering exhaust manifold, plenum chamber, 90mm throttle, Garrett W2A cooler, Surecam custom, autronic SM4, Bosch 120lb, Crane HI-6, LX-92, LM-1, Turbosmart Reg, 2x bosch 044, turbosmart 48 gate. 470kw+ @ 18PSI |
||
| Top | |
||
| rizzo |
|
||
|
cheers mate. that clears that issue up.
_________________ If it moves, weld it down! |
||
| Top | |
||
| EBXR8380 |
|
|||
|
They are not cheap though...
_________________ As in ZOOM 126 edition |
|||
| Top | |
|||
| data_mine |
|
|||
|
I'm looking at getting one too, as I'm waiting on the last of my ECU tuing gear to arrive (an ECU emulator), I'll need a AFR meter to do anything meaningful.
Could one, get a wideband O2 sensor, use it in the stock ones place, and then run the EEC and a meter from it? or will the EEC check a wobbly?
_________________ 1998 DL LTD in Sparkling Burgundy, daily, 302W, stereo, slow |
|||
| Top | |
|||
| ebs_4l |
|
||
|
no problems, talking only from experience with a LM-1, they have two outputs, which can be programmed to read whatever you want..
which means, one can emulate a narrowband std sensor output. which is programmed from factory, and the other can be a 0-1v linear output required for an autometer a/f gauge
_________________ EB 4L, 8.4:1, R154, GT4202r, 4in exhaust, Greenslade Engineering exhaust manifold, plenum chamber, 90mm throttle, Garrett W2A cooler, Surecam custom, autronic SM4, Bosch 120lb, Crane HI-6, LX-92, LM-1, Turbosmart Reg, 2x bosch 044, turbosmart 48 gate. 470kw+ @ 18PSI |
||
| Top | |
||
| xr8ute |
|
||
|
data_mine wrote: Could one, get a wideband O2 sensor, use it in the stock ones place, and then run the EEC and a meter from it? or will the EEC check a wobbly?
The TechEdge WBO2 I've got has a simulated narrowband output. To be honest though, I haven't hooked used narrowband output yet....I've always just run it without any signal going back to the EEC for that side of the engine. |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 11 guests |
