|
| spvd02 |
|
||
|
If I were to get PH4499 extractors and a 2.5" exhaust (the usual), not including the cat, where will the improvement in power be?
I'm hoping for bottom end to mid-range, because when dragging a VS commodore, by the time we hit 60km/h they're already in their top-end power-range, which sux, coz they pull ahead about a body length before we get into our top end range. I got beaten by my friend's VS Commodore wagon with 2 people in it. I was driving on LPG (tickford), which is hardly slower than petrol, and I have a crow cam. I still run a standard exhaust, though, and he has extractors and a 2 1/2". It's made a huge difference for his car. I'm hoping it will make a similar difference for mine. He shouldn't be beating me from the lights! |
||
| Top | |
||
| twr7cx |
|
|||
|
Pacey comps give good low down and mid range power increase (sorry but I can never remember the part number of the standards and comps, so I just callthem standards and comps not PH4499 and PH4480).
|
|||
| Top | |
|||
| smoke_ |
|
|||
|
ph4499 are supposed to be better low-end aren't they, cause i have 4480's and the top end is better not bottom end.
I have the 4480's, highflow cat and 2.5in system, and i picked up power and torque everywhere but <1500rpm.
_________________ NEW RIDE - FPV FG F6 6spd Auto. 12.26@114MPH, 1.88 60FT on Cheapy Tyres with 38PSI - Stock except K&N filter! |
|||
| Top | |
|||
| MYLO_XR6 |
|
||
|
dont expect any bottom end torque with a 2 1/2 system!!! go for the 2 1/4"
you cant rev the car past 6000 anyway so why run a 2 1/2 ?, youll be suffering from backpressure starvation and youll loose torque (especially if its a stock 6.......please dont include a pod filter as a modification  )
i know someone who installed a 2 1/4 (inner diameter) and it goes noticibly well
_________________
|
||
| Top | |
||
| dazza2924 |
|
|||
|
how much would that cost to get a 2 1/4" and extractors btw???
|
|||
| Top | |
|||
| MYLO_XR6 |
|
||
|
$327 + 22 delivery off ebay for extractors
exhaust system, from 300-500 with the exhaust i would just go for a 2 1/4" inner diameter with a cat only! i wouldnt bother with resignator or muffler, but the EPA will f**k u up, so probably add a resignator
_________________
|
||
| Top | |
||
| fnp |
|
|||
Age: 39 Posts: 4401 Joined: 25th Mar 2005 Ride: BA XT, BA XR6T, ED Ghia 5.0 Location: Perth |
Resonator.
_________________ What's the difference between a Holden and a sheep? It's less embarrasing getting out of the back of a sheep.. |
|||
| Top | |
|||
| MYLO_XR6 |
|
||
|
Allright bro! is this suppost to be Microsoft Word Spell check?
_________________
|
||
| Top | |
||
| spvd02 |
|
||
|
What is the standard inner exhaust diameter? Less than 2 1/4?
|
||
| Top | |
||
| Steady ED |
|
|||
|
spvd02 wrote: What is the standard inner exhaust diameter? Less than 2 1/4?
2.25, with press bends, me thinks. Why you'd go 2.25 mandrel, I'll never know... 2.5" is tried and tested. Lost bottom end torque with just a 2.5" exhaust? Pffft... A 2.25" mandrel bend system will cost MORE then a 2.5", cause they'll have to custom make it, and that's if the shop even has a mandrel bender (HA). Just get an off-the-shelf 2.5" of whatever brand you can get for the best price...
_________________ ED XR8 Sprint - S-Trim, V500, 249rwkw |
|||
| Top | |
|||
| kurucuperformance |
|
||
|
The extractors mainly determine where you would be getting most of your power in ur power curve...exhaust will only give u between 1-5 kw and extractors will do same..
|
||
| Top | |
||
| spvd02 |
|
||
|
Tomorrow a 2.5" cat back system will be fitted. Can't afford extractors yet, so I'll wait a while. It should free it up a bit anyway.
Got a K&N air filter today, and she's definitely got more throttle response. It's not awesome, but it's noticeable. The torque curve seems more linear as well. Should I try push 'em to modify my cat as well? I think I might do that; make the outlet 2.5" instead of 2.25". Every little bit helps. |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 110 guests |
12.06@120MPH
