|
| Ernie |
|
||
|
Hi All,
I have a problem with my EB Fairmont Ghia climate control air con. It appears the fan speed hunts, ie from low to hi on a cycle. It does it whether in auto mode or manual fan speed selection. Any idea on possible cause of fault. Thanks. |
||
| Top | |
||
| Interceptor |
|
||
|
possibly a f**k fan speed controller
_________________ Banned |
||
| Top | |
||
| philaddis |
|
|||
|
Run diagnotic and see if any errors are logged.
Bottom right button (inside the panel door) and off to start diagnotics and then note any codes that are logged, ie E1, E2.......etc, then get back to us!
_________________ ED XR8 Spri-mitatio-nt |
|||
| Top | |
|||
| Ernie |
|
||
|
Not sure on how to run diagnostics.
Please adivse details. Ford quoted $290 for a fan speed controller, I don't want to spend the money if its not the problem. Thanks. |
||
| Top | |
||
| paul.efgli95g/g |
|
||
|
the climate controle have self diagnostic, the ECU will not pick these fults up, i will try to get the instructions to runt the diag's tomorrow.
see if you can go to another source for genuane part, eg motor traders.
_________________ For
|
||
| Top | |
||
| Ernie |
|
||
|
Thank you for your response.
The problem seems to have recitified itself. However I would'nt mind having the diagnostic info, just in case |
||
| Top | |
||
| paul.efgli95g/g |
|
||
|
sorry i took so long, but here it is in full. it is a small system not like a ECU.
engine at operating temp. for EA to ED - Hold the FLOOR button for EF to EL - Hold the MODE button and press the OFF button. Release both buttons at the same time. any eror codesheld in memory will be displayed in the LCD Display.. for next error code press AUTO button To quit press AUTO button untill no more codes are displayed. To clear codes, initate self test twice. FULT CODES E1- Electronic Controle unit fulty- RAM air to windscreen E2- blend Door Movement out of range- check for obstruction E3- Cabin temp sensor open circut E4- Solar load sensor short circut E5- Ambient Air temp sensor open circut E6- Evaporator Temp sensor open circut E7- Engine temp sensor open circut
_________________ For
|
||
| Top | |
||
| Ernie |
|
||
|
Many thanks Paul, you've been a great help.
|
||
| Top | |
||
| fordzatmyplace |
|
||
|
Ernie wrote: Not sure on how to run diagnostics.
Please adivse details. Ford quoted $290 for a fan speed controller, I don't want to spend the money if its not the problem. Thanks. i have a cheap fan speed controller if you want it...
_________________ ^^^ What He Said
|
||
| Top | |
||
| Ernie |
|
||
|
At this point I don't think I need it as the problem has disappeared on its own.
However, I'll keep it in mind Thanks |
||
| Top | |
||
| fordzatmyplace |
|
||
|
Ernie wrote: At this point I don't think I need it as the problem has disappeared on its own.
However, I'll keep it in mind Thanks hmmm send me a pm if you need it. previos experince has shown me that problems don't just dissapear!
_________________ ^^^ What He Said
|
||
| Top | |
||
| EL-FAIRMONT-GHIA |
|
||
|
paul.efgli95g/g wrote: sorry i took so long, but here it is in full. it is a small system not like a ECU.
engine at operating temp. for EA to ED - Hold the FLOOR button for EF to EL - Hold the MODE button and press the OFF button. Release both buttons at the same time. any eror codesheld in memory will be displayed in the LCD Display.. for next error code press AUTO button To quit press AUTO button untill no more codes are displayed. To clear codes, initate self test twice. FULT CODES E1- Electronic Controle unit fulty- RAM air to windscreen E2- blend Door Movement out of range- check for obstruction E3- Cabin temp sensor open circut E4- Solar load sensor short circut E5- Ambient Air temp sensor open circut E6- Evaporator Temp sensor open circut E7- Engine temp sensor open circut I carried out this procedure (after reading your post) when my heater would not work. Upon carrying out the procedure my climate control system appeared to reset itself and now the heater functions perfectly. Thank you very much for saving me a trip to the mechanic! |
||
| Top | |
||
| arm79 |
|
|||
|
EL-FAIRMONT-GHIA wrote: paul.efgli95g/g wrote: sorry i took so long, but here it is in full. it is a small system not like a ECU. engine at operating temp. for EA to ED - Hold the FLOOR button for EF to EL - Hold the MODE button and press the OFF button. Release both buttons at the same time. any eror codesheld in memory will be displayed in the LCD Display.. for next error code press AUTO button To quit press AUTO button untill no more codes are displayed. To clear codes, initate self test twice. FULT CODES E1- Electronic Controle unit fulty- RAM air to windscreen E2- blend Door Movement out of range- check for obstruction E3- Cabin temp sensor open circut E4- Solar load sensor short circut E5- Ambient Air temp sensor open circut E6- Evaporator Temp sensor open circut E7- Engine temp sensor open circut I carried out this procedure (after reading your post) when my heater would not work. Upon carrying out the procedure my climate control system appeared to reset itself and now the heater functions perfectly. Thank you very much for saving me a trip to the mechanic! Doing this proceedure on an e-series will reset the blend door motor calibration. Sometimes the climate control unit looses the high and low value memory, and this is the only way to reset it. Although as Paul said, the car must be at operating temperature, otherwise the internal sensors will not pickup the hot/cold air and adjust the blend door calibration correctly. So if you do this same things when the car is cold, it will screw the calibration. |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: AU86 and 71 guests |
