|
| DrE |
|
|||||||
|
Just finished installing my bbm and piping about a week ago, but have had a few dramas since doing it. While it had the mpefi manifold on it was fine, put the bbm on and it lost power above 3krpm, would rev but not go anywhere, ended up being the distributor had about 3mm of play left to right up and down, replaced that did the timing and it makes power all the way up to 5k, now during this process the timing has been really hard to do, it doesnt want to stop pinging, even now it will still ping at high rpm on a hot day, ive replaced: distributor, plugs, fuel filter, map sensor, air intake temp sensor, tps, injectors. Could the o2 sensor cause the pinging? or should i just throw the old manifold back on, cause it never pinged while that was on, but the bbm does make more seat of your pants power. If anyone has any suggestions that would be great. anyway on for the pics. sorry about the quality where taken on my phone
_________________
|
|||||||
| Top | |
|||||||
| XR6EB |
|
||
|
what ecu are u using?
When i had this conversion done i had the same problem. I had the standard eb xr6 ecu, together with a EMS unit. The standard ecu ended up being removed cause it apparently was causing the problems. Once removed and tuned again , the problem was solved...now its a pig to start on cold days!
_________________ EB S XR6
|
||
| Top | |
||
| Ready? |
|
|||
|
are you using premium?
_________________ I hope she's hotter than two monkeys having sex under a wool blanket in a hot sauna
|
|||
| Top | |
|||
| Blu Falc |
|
|||
|
the problem is your not running the EL ECU, unless you go aftermarket or keep it switched to the short runners or put an EL ECU in your going to have this problem.
I ended up not doing the BBM conversion because I dont have smartlock and the bypass was to expensive. But if you have smartlock it wont be a problem |
|||
| Top | |
|||
| DrE |
|
|||
|
yea i dont have smartlock either (s1 eb), ive been fiddling with timing and so far so good its switched on high runners and not pinging even at temp so ill see how it goes, and its still making power the whole way through, it feels quicker than the older manifold but i have no way to measure if it is or not, just out of wonder, on high runners does the ecu not have the correct fuel maps to suit more air being pulled in or is it something totally different?
_________________
|
|||
| Top | |
|||
| Blu Falc |
|
|||
|
EL's and EF's run different timing and fuel maps depending on where the runners are, to get the most out of your conversion buy a smartlock overide from 66 coupe and an EL computer. This will also allow you to run thermo fans later on as well
|
|||
| Top | |
|||
| DrE |
|
|||
|
i already have thermos, but they are permanently on at ignition on position, how much do the overrides cost? im guessing i could pickup a el ecu quite cheaply from the wreckers?
_________________
|
|||
| Top | |
|||
| Blu Falc |
|
|||
|
EL ECU's are cheap on ebay, I have seen cop EL ECU's got for $80 or regular ones for $35. The overides are $150 from 66 coupe or $350 from JMM. with the EL ecu the thermos will run properly
|
|||
| Top | |
|||
| DrE |
|
|||
|
hmm think ill have to save my pennys and grab a smartlock bypass, is there anyway around it bar from putting the old manifold back in for now?
_________________
|
|||
| Top | |
|||
| Blu Falc |
|
|||
|
keep the runners switched for now so it doesnt ping
|
|||
| Top | |
|||
| DrE |
|
|||
|
ok thanks for the info, never thought of that and ive been wracking my brain for weeks, muchly appreciated, btw runners on low would = a normal mpefi manifold?
_________________
|
|||
| Top | |
|||
| Blu Falc |
|
|||
|
yer, enough to make sure it doesnt ping. this is what voxace did untill he put an EL computer in it as he had the same problem as you
|
|||
| Top | |
|||
| voxace |
|
|||
|
Yeah that's what I did (short runners).
Oh and I noticed you got my old headlights on... |
|||
| Top | |
|||
| smoke_ |
|
|||
|
painting the bbm black looks sweet as, it blends in with the rest of the plastic.
you should run it up at willowbank now dude!
_________________ NEW RIDE - FPV FG F6 6spd Auto. 12.26@114MPH, 1.88 60FT on Cheapy Tyres with 38PSI - Stock except K&N filter! |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 77 guests |
12.06@120MPH