Fordmods Logo

need a lil it of help 

 

Page 1 of 1 [ 2 posts ] 

 
 Post subject: need a lil it of help
Posted: Sun May 14, 2006 1:32 pm 
Fordmods Newbie
Offline

Posts: 5

Joined: 26th Apr 2006

Gallery: 1 images

Ride: EF

Location: Melbourne
VIC, Australia

ok i just need to know wat type of amp i need to run spreakers and subs..

The 2 amps im lookin at are:




2 CHANNEL AMPLIFIER 1600WATTS
HIGH PERFORMANCE MOSFET POWER CAR AMPLIFIER
FEATURES:

2 x 800 watts
2 X 70 RMS
Bridgeable output
Low level input
Input ground isolation
Noise rejection circuit
2-channel RCA input/out
Bass/Treble/Gain controls
ST/BRID Translate controls
Dimensions (L X W X H) 280 x 247 x 49mm
Out put power 1600 Watts (800W x 2 @ 4 Ohms)
800 watts (400W x 2 @ 4Ohms)

Bridged output power max: 800wats (800W x 1 load@ 4 ohms)
Input sensitivity: <250mv
Signal /Noise Ratio: 97dB
Speaker Impedance: Stereo output 2-16 Ohms
Bridged output 4-16 Ohms






and then....


4CH 1400WATTS CAR AMPLIFIER
4 Channel RCA input/output
Maximum output power: 4 x 350watts
High performance mosfet power amplifier
High pass filter/Low pass filter/FULL/SUB/GAIN controls
Thermal overload protectionAA
LPF control-adjustable frequency 50Hz-250Hz
HPF control-adjustable frequency 120Hz-3KHz
Super BASS boost transition control switch
Frequency response: 10Hz-20KHz
Input sensitivity: <250mv
Siganl ratio: 98dB
Serperation scale: >50dB
Speaker impedance: Stereo: 2-16Ohms
4-16Ohms

Dimensions: 330(L) x 257(W) x 60(H)mm
Output Power RMS: 340watts (85W x 4 load 4ohms)
Output Power MAX 3400watts (850W x 4 load 4ohms)
Bridged output power (RMS): 340watts (170W x 2 load 4ohms)
Bridged output power (MAX): 3400watts (1700W x 2 load 4ohms)
4Channel independent input and output
Adopting gold plated lotus pluginput terminal, low level input
Stereo/Bridged output transition
High power tube for tonal quality
Electronic Protective Circuit against Short Circuiting DC Offset, excess temperature, and overload
Power On & Protection Led Indicators




now im not looking at gettin anyhitng fancy for the time being but with these two types of amps would i be able to run this sub:

15" subwoofer
Max Power 1200Watts
Metallic P.P Injection Cone
Response Frequency 30-2000Hz
Sensitivity 90 + 3dB
Impendence 4 ohms
Twin Magnet 100 OZ
Voice Coil 50mm
RMS 600Watts

12" subwoofer
Max Power 1000 Watts
Metallic P.P Injection Cone
Response Frequency 30-2000Hz
Sensitivity 90dB
Impendence 4 ohms
Twin Magnet 100 OZ
Voice Coil 50mm
RMS 500Watts


and the speakers... wat type of power, for example if it says 400w 4-way can i run them or 300w 3-ways




i just want 2 6 inch in the front and 2 in the back and possible 2 12 inch subs... so how many of those amps will i need?
do i need 6 x 9 in the back and whats the max size that fits in the door pods? would i be able to fit a 6.5 or an 8 in?


so would this sound good and clear in the car load? and also is BOSS a good brand?

thanx for any help
Top
 Profile  
 
 
Posted: Sun May 14, 2006 1:48 pm 
Getting Side Ways
Offline

Posts: 2555

Joined: 7th Nov 2004

Location: No Where
NSW, Australia

Stay clear of BOSS for speakers they arent that well sounding. If you want some cheap but not bad sounding speakers look for Pioneer or jaycar brnaded ones.

If you're on a budget i'd suggest a monoblock to run the 2 subs and a 4 channel amp to run the front speakers. There is not so much need to amp up the rear speakers unless of course the back seats are used fairly regularly.
Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 2 posts ] 

Who is online

Users browsing this forum: No registered users and 24 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Tue Dec 24, 2024 2:56 am All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names