|
fairmont599 |
|
||
Posts: 1135 Joined: 27th Oct 2005 |
ok fellas got a bit of a problem here
went to replace my leads on my 95 fairmont today an i must say C*** of a spot to get to. but anyway when i went to remove the lead for cylinder 3 i noticed it was plugged into plug 4 on the coil pack. the samne applied for cylinder 4 being plugged into plug 3 on the coil pack. now im not rocket scientist but that is odd, the car has run rough now an again ever since the reco motor was put in nearly 7000kms ago. i replaced the leads the same as i found them, do you think that my running rough problem may be because of the mechanics stuff up as the problem hasnt gone away it still runs rough now an again. new leads on today an plugs were done less than 10,000kms ago. the car surges still like it used to. not all the time but now an again. does it at idle too. |
||
Top | |
Krytox |
|
|||
|
I think 1/2/ - 3/4 - 5/6 fire in groups, It shouldn't 'really' affect it but Its nicer to have it the right way!
_________________ Carefree, we may not be number one, but we're up there. |
|||
Top | |
Pulco |
|
||
|
put them on the right way
_________________ |
||
Top | |
fairmont599 |
|
||
Posts: 1135 Joined: 27th Oct 2005 |
yea i will be tomorrow. not looking forward to it. theres a sharp thing down there an i managed to catch me finger on it an now i have a huge gash in it. bloody has to be in a prick of a spot eh?
|
||
Top | |
MARK.TANIA |
|
||
|
when i change the leads on mine and the wifes ef. i took the hole air box off that way i could get my hands down were the air box was.it is a bit of extra work but it also helps to put the leads on tight and less skin lost as well
|
||
Top | |
fairmont599 |
|
||
Posts: 1135 Joined: 27th Oct 2005 |
yea i did that as well, still lost skin and blood lol
|
||
Top | |
phongus |
|
|||
|
dont u just hate it when u put so much money and blood onto the car only to have the car run not rite......but yeah best way is to pull the air box out. wasnt as hard since i had my mate push the leads down as i placed them in the right position.
phong =P~
_________________ phongus = Post whore 2006 |
|||
Top | |
Gaz |
|
||
|
if they werent on the correct plug then you would know about it, would be more than a little rough.
_________________ 2007 Steel BF Ghia MKII V8 - 19" GTP's + Superlows |
||
Top | |
naughtyfalcon |
|
|||
|
ford put two leads around the wrong way on my ea,i didn't notice a thing till i changed the cam shaft,they had reversed leads 2 and 3..s**t it ran well after we changed them over.
they seem to learn around things like this for some reason.
_________________ |
|||
Top | |
fairmont599 |
|
||
Posts: 1135 Joined: 27th Oct 2005 |
well iv fixed the leads problem still surges, still idles a little rough sometimes. so now back to square one.
could the cat be f**k an causing it to run badly. as the car has what seems to be stock exhaust replaced back in 2001 with super cat mufflers. over the past 6 months it has begun to drone when driving at 1800 - 2200 rpm an been getting worse so im havin a stab in the dark an sayin the cat is rooted. could it be the cause of my problem? |
||
Top | |
tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
Krytox wrote: I think 1/2/ - 3/4 - 5/6 fire in groups, It shouldn't 'really' affect it but Its nicer to have it the right way!
1 and 6 2 and 5 3 and 4. the pistons on the same throw are paired |
||
Top | |
MARK.TANIA |
|
||
|
it might be the cam angle sencer .that fixed both of my ef's
|
||
Top | |
Who is online |
---|
Users browsing this forum: No registered users and 71 guests |