|
| phongus |
|
|||
|
hey everyone. im still wrecking the EA and someone asked for climate control parts and that includes the damn blend door motor.....i located it on top of the heater box but how the hell is the box connected to the chassis? its so damn tight....i cant find any screws that hold it down. is it like glued in EXTREMELY or are there screws outside the car that somehow hold the thing in? i just need to remove the blend door motor but its proven difficult. managed to lacerate my thumb in the process.
cheers everyone phong =P~
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| Rapier |
|
||
|
if its anything liek ef/el screws will be on the firewall of teh car 5 11mm bolts, u will need to take heater hoses and A/C lines out as well.
good luck caus its a prick of a job |
||
| Top | |
||
| snap0964 |
|
|||
|
The BDM is held on by rivets - the ones I got from the wreckers I used a sharp thin chisel between each leg and the heaterbox to shear through the rivets - the BDM legs may need slight straightening, but you could possibly butcher the heaterbox - which is not good obviously if they want the heaterbox as well. Then you remove the fan speed controller, etc. The adaptor of the blend door shaft needs to go with the BDM.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| phongus |
|
|||
|
yeah thanks tim.....i saw like 5 or 6 bolts thingy sticking out into the engine bay....i unscrewed it but hell it didnt move after i used a hammer to bash the screw in. ill give it a shot again tomorrow cheers....
snap0964 thanks mate. but i think im going keep the heater box just incase.....i want to learn how to remove things the proper way at the moment so that when i do need to change the BDM in my EL (hope i never do) i know something and work on it. but if it gives me the s**t tomorrow.......bye bye heater box. phong =P~
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| snap0964 |
|
|||
|
No probs dude - Dave (the_scotsman)has some pretty good heaterbox pics here: http://www.fordmods.com/forums/viewtopi ... c&start=20 .
All E series heaterboxs are pretty much the same, except on yours you'll find the vacuum solenoid unit sits over on the recirc air box.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| phongus |
|
|||
|
cheers snap =D and damn that was a lot of wiring.....i wonder if it would look the same if i took all the wires out of the removed dash. ah wells
anyways ill keep it updated to see if im either cursing and lacerate my hands again or if i got it out. thanks phong =P~
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| Rapier |
|
||
|
u will have to wriggle the box a bit once the screws are ondone you notice it being loose, then you will have to get the heater hoses off and ac lines otherwise it wont move far. have fun
|
||
| Top | |
||
| phongus |
|
|||
|
well i never even had the chance to put a hammer to it today cause i had work....hopefully i can do it some time soon.
phong =P~
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| John_xr6 |
|
|||
|
did you undo the right nuts? it should pull through fairly easily. i wouldnt hammer it either unless you want to break it
 als the blend door motor is held in with screws onlt the bracket is pop riveted in. unless the person wants the bracket as well to convert their old heater box.
_________________ 2005 Toyota Hi-Ace aka ICE CUBE |
|||
| Top | |
|||
| KRUPTD |
|
||
|
Last week i replaced a blendor motor in a EF fairmont ghia.Didnt remove the heater box at all.Just removed the dash and column and kick panels and other little fidly parts.Then cut part of the padding so i had more room.Then i used a philips screw bit and a small quarter spanner and removed all 4 screws which held the blendor motor to the bracket.Slipped the new one in lined it back up and screwed it back down.And refitted the dash and there you go.Nice and simple.But if you dont want to cut your padding well you will have to disconnect your heater pipes and a/c pipes too,that means running your gas out of the system.And its quiet pricey to get the a/c system regassed.
_________________ COMING SOON,XD WITH A TURBO...CLEVO STYLE |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 31 guests |
