|
| AdamN |
|
||
|
I have the Rspec3... I used 6 shims. Just measure your clearances with 6 shims... if they're within the acceptable range.. then she's gold
Otherwise add/remove shims and try again. |
||
| Top | |
||
| Steady ED |
|
|||
|
Think I had 4 non-ford 'shims' (washers) plus the factory.
HLA wasn't falling out the arm, and I had no problems with lifter noise, drove it around like that for about, f**k, 15,000kms?
_________________ ED XR8 Sprint - S-Trim, V500, 249rwkw |
|||
| Top | |
|||
| efbignik |
|
|||
|
it just seams that the vavles open to far at full lift
_________________ EFBIGNIK 145.9 RWKW Falcon / 16.27 @ 86.72mph (Stock)
|
|||
| Top | |
|||
| Mhgill |
|
||
|
isn't it fun shimming cams?
Ring jeysen, he's always happy to help. Make sure your getting the measurements + math correct. Took me 2 full days to put mine in. It's a head f**k, but you'll get there.
Ring Jeysen.
_________________ EL Fairmont Ghia 5.0 |
||
| Top | |
||
| efbignik |
|
|||
|
i'll say i'v been on the fone to jaysen like 3 times already
_________________ EFBIGNIK 145.9 RWKW Falcon / 16.27 @ 86.72mph (Stock)
|
|||
| Top | |
|||
| Molloy |
|
|||
|
U winning yet champ??
_________________ SS Inductions CAI, K&N Filters, M-spec FMC, Turbosmart BOV, 8psi capa tune, X-force cat. |
|||
| Top | |
|||
| efbignik |
|
|||
|
i think so
_________________ EFBIGNIK 145.9 RWKW Falcon / 16.27 @ 86.72mph (Stock)
|
|||
| Top | |
|||
| AdamN |
|
||
|
Don't you just love learning new stuff on the fly?
 :D
Well I do hehehe |
||
| Top | |
||
| mickysacca |
|
|||
|
dont worry mate, had the same dramas with my R3 2 weeks ago. me and the old man were cursing at each other in the end but we ended up fitting 5 shims on both exhaut and intake rockers.
This left us with about 0.9mm and 1.1mm of adjustment on the exhaust and intake respectively. Dont worry so much. i was worried too but started her up, heard those damn taps and within about 10 kays of driving she was all sweet Now after 2 weeks all is sweet. Hope i was of any help |
|||
| Top | |
|||
| Mhgill |
|
||
|
How'd you go? Got it done?
My custom RPD is astage 1.5 basically, i had 3 shims on the inlet and 4 on the exhaust. My lifters kept falling out, i just taped them in. It's still rattly, but i think thats just the lifters themselves.
_________________ EL Fairmont Ghia 5.0 |
||
| Top | |
||
| Whiteknight1 |
|
|||
|
Hows the shims goin Efbignik?
_________________ Back in an E series! |
|||
| Top | |
|||
| Shum's EL |
|
|||
|
yeah he got it all worked out... 5 shims on the intake side and 6 on the exhaust (or visa versa)
his EF dont go to bad at all now
|
|||
| Top | |
|||
| efbignik |
|
|||
|
Whiteknight1 wrote: Hows the shims goin Efbignik?
yeah mate what shums said thay where just sweet then i drove to melb after a long drive thay rattle a bit but i think it's just the liftters but i'll never do it a again to much of a head f**k for me give me my grain any day i can tell you any thing about it just looking at what else i can do and still keep it on go gas the r3 loves the go gas i mean yeah it still runs heaps better on PULP but thats the way i will all ways be but go gas is for cruzing and PULP is for racing thats the way i wantted it
_________________ EFBIGNIK 145.9 RWKW Falcon / 16.27 @ 86.72mph (Stock)
|
|||
| Top | |
|||
| Shum's EL |
|
|||
|
efbignik wrote: but go gas is for cruzing and PULP is for racing
couldnt have put it better myself ha ha |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 81 guests |
