|
| greg302 |
|
||
|
what is the imbalance on a eb 5litre windsor, 50 oz?
_________________ 347, crane cam, Pro topline 180 heads, Edelbrock victor efi intake, 80mm C&L maf, 75mm tb, 30lb injectors and 1/4 horse |
||
| Top | |
||
| XR9UTE |
|
||
|
yep.
|
||
| Top | |
||
| greg302 |
|
||
|
thanks pete
_________________ 347, crane cam, Pro topline 180 heads, Edelbrock victor efi intake, 80mm C&L maf, 75mm tb, 30lb injectors and 1/4 horse |
||
| Top | |
||
| XR9UTE |
|
||
|
no wuckers greg!
Basically from '82 5.0's went with the 50oz imbalance because the crankshaft centre counterweights were shrunk down in mass. This necessitated the imbalance to be moved outside the engine...on the flywheel and balancer. If you get a chance to look at an old 302 crank next to an '82-up type you'll see what i mean. Also note that these late blocks are a considerably lighter casting, 25lb's lighter in fact. This is why the factory engineering rating was reduced from 500hp to 350hp on the late blocks. Pete. |
||
| Top | |
||
| greg302 |
|
||
|
pete can u give me the run down on how to activate the thermos with the tweecer. i want them to switch on to high when they come on. so i can get rid of the craig davies switch on it thanks
Greg
_________________ 347, crane cam, Pro topline 180 heads, Edelbrock victor efi intake, 80mm C&L maf, 75mm tb, 30lb injectors and 1/4 horse |
||
| Top | |
||
| XR9UTE |
|
||
|
Yep, pin 41 will drive the low side of your fan relay(use a relay with a flyback diode and at least 40A capacity). The parameters are in Caledit...I will post the settings when I get home.
Pete. |
||
| Top | |
||
| greg302 |
|
||
|
ok no probs
_________________ 347, crane cam, Pro topline 180 heads, Edelbrock victor efi intake, 80mm C&L maf, 75mm tb, 30lb injectors and 1/4 horse |
||
| Top | |
||
| XR9UTE |
|
||
|
Sorry I forgot.
Pete. |
||
| Top | |
||
| greg302 |
|
||
|
when ever you get a chance mate
_________________ 347, crane cam, Pro topline 180 heads, Edelbrock victor efi intake, 80mm C&L maf, 75mm tb, 30lb injectors and 1/4 horse |
||
| Top | |
||
| XR9UTE |
|
||
|
Hi Greg,
Find these in the Scalars list. This is how I set my 1DDC in the ute to turn on the fans at 190F and off again at 180F. Fan_high_speed_any_load_temp = 180 Fan_high_speed_high_load_temp = 190 Fan_low_speed_temp = 180 Fan_present = 1 Fan_two_speed_enable = 1 Pete. |
||
| Top | |
||
| greg302 |
|
||
|
thanks mate ill give it a go
_________________ 347, crane cam, Pro topline 180 heads, Edelbrock victor efi intake, 80mm C&L maf, 75mm tb, 30lb injectors and 1/4 horse |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 40 guests |