|
| twase |
|
|||
|
I am having trouble installing a aftermarket arial, its a semi automatic Aerpro AP3 which is sold as a direct factory replacement. The arial has basically two wires coming from the motor apply power one way and it rises until you remove power and reverse the power and it falls until you remove the power.
Looking at the arial connector from the NL dash both lines seem to have power on both while the ignition is on and for a little while after the ignition is turned off. I have an after market HU but I have the arial signal connected to the correct wire on the dash loom. Does anyone know how this is supposed to work?
_________________ BF Fairmont Ghia Series II update. |
|||
| Top | |
|||
| huggiebear |
|
|||
|
ok from my understanding the reason it has power for a short amount of time is because the arial closes when the car is turned off, the power therefore allows the arial to drop down hidden, with an aftermarket headunit, providing it had an electric arial wire (kenwood do) which is a different wire to the remote wire for an amp (remote is powered when stereo is on, arial is only powered while the stereo is on) if this only works one way i sujest installing an arial switch such as what EB's use which allow you to put the arial up and down yourself.
you say they both have power... do you think it needs 2 sets of power to stay up? and when one switches off it drops? i sujest having a much around with it before you install it. i have one in the back seat of my falcon at the moment, ill have a look at it tomorrow and see if i can work it out |
|||
| Top | |
|||
| twase |
|
|||
|
Thanks but I dont see how this can work , unless the BEM output is sensing curent, the both rise and fall together from what I can see so there is never a voltage difference between the two to drive the motor. Putting a lamp across the two it never lights.
I might have to have another look at the arial input to the BEM perhaps my HU is not giving the signal to raise the arial.
_________________ BF Fairmont Ghia Series II update. |
|||
| Top | |
|||
| snap0964 |
|
|||
|
I think you'll find that you'll need a load across the two aerial output wires - when I installed an EF high series BEM in the XH, I found I was getting strange readings with a meter. I plugged in a spare ford aerial (broken mast), ran it also with the half height switch, and it ran as per normal.
At the time, I was already running an aftermarket semi automatic aerial, so what I did was bypass the semi auto circuit and ran it directly off the two motor wires. Normally the motors have an overrun clutch, so it shouldn't be an issue. Only thing is it doesn't have half height (just extends to full height), but it does raise and lower with a few seconds of overrun. I'd say like you've said, that the BEM may run current sensing, and possibly a timer as well. The ford aerials are probably matched to the BEM, although with theory it shouldn't make a huge diff. So after the novel I've written above, I'd suggect trying it by tapping power directly onto the motor wires. EDIT: After reading your post properly again: Have you plugged it and tried running it ??
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| twase |
|
|||
|
Yes I have tried it and there is no movement on the arial. , can't think atm my 7yo dog just got run over and killed by an 87yo granny.
_________________ BF Fairmont Ghia Series II update. |
|||
| Top | |
|||
| huggiebear |
|
|||
|
that sux dude, sorry to hear
|
|||
| Top | |
|||
| twase |
|
|||
|
I have found the BEM is the problem, R79 (0.47ohm 2w had fried) I will replace it and see hoew it goes.
Thanks Huggie for the supprt.
_________________ BF Fairmont Ghia Series II update. |
|||
| Top | |
|||
| huggiebear |
|
|||
|
no problems... whats R79 (0.47ohm 2w had fried) ???
i have my BEM infront of me now, (i pulled it out of my wreck last week and took pics of it 1 hour ago - seems everyones BEM's are stuffing up) and i cant find and numbers or lettering unless its inside |
|||
| Top | |
|||
| twase |
|
|||
|
It is inside the BEM its the 2 watt resistor.
_________________ BF Fairmont Ghia Series II update. |
|||
| Top | |
|||
| huggiebear |
|
|||
|
ah ok, ill pull it apart to have a look see
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 16 guests |
