Fordmods Logo

rattling/knocking sound around P/S pump 

 

Page 1 of 1 [ 7 posts ] 

 
 Post subject: rattling/knocking sound around P/S pump
Posted: Mon Oct 02, 2006 4:13 pm 
Oompa Loompa
Offline

Posts: 39

Joined: 27th Jul 2006

Ride: Falcon

Location: melbourne
VIC, Australia

When starting the ef cold theres a rattling/knocking sound from around the power steering pump, then after a few minutes it stops. Replaced pump with one from a wrecker which seemed to have a new pulley on it and even though it wasnt as bad it still did it, any suggestions would be helpful, thanks.
Top
 Profile  
 
 
Posted: Mon Oct 02, 2006 11:13 pm 
Getting Side Ways
Offline
User avatar

Posts: 887

Joined: 8th Aug 2006

Ride: Falcon

Location: Central Highlands
QLD, Australia

spray some water or CRC belt grip on the belt while engine at idle, if the noise goes away, it's a worn belt.

Commom problem on EF/EL's for a worn belt to make wierd noises on that big pwr str plastic pulley.

cheers............

 

_________________

97 EL Fairmont 4l OHC .Silver.
Exhaust: Pacemaker's, 2.5" exhaust and Hiflow cat
Intake: FRAM AIRHOG , EL GT snorkel
XR6 300kpa fuel reg Stg 2 Auto Shift Kit.6DJA ECU
PM in Qld looking too buy Toyota 4*4 SR5 Dualcab Hilux 91-97 with 2.8l diesel engine/5spd manual

Top
 Profile  
 
 
Posted: Tue Oct 03, 2006 12:40 am 
Getting Side Ways
Offline
User avatar

Age: 38

Posts: 557

Joined: 20th Aug 2006

Gallery: 4 images

Ride: EF

Location: Keilor, Melbourne
VIC, Australia

I agree, sounds like the belt may be worn. Check your pulley over for hairline cracks as when the belt applies pressure to this crack, could cause your knocking.

To check if its internals of the pump, take the cap off. If the noise is noticably louder with cap off, then you picked up a dodgy pump. If the noice is no different then the pump is pumping fine.

I rebuild pwr steer pumps and racks, and ive found that half the time its either the pulley, or the other half is a blown o'ring inside causing valve plates to move when they shouldnt.

 

_________________

<img src="http://i29.photobucket.com/albums/c260/demoniquekryes/Bothcars1.jpg" alt="Photobucket - Video and Image Hosting"><br><br>

Top
 Profile  
 
 
Posted: Tue Oct 03, 2006 7:22 am 
Oompa Loompa
Offline

Posts: 30

Joined: 18th Feb 2006

Location: mel
VIC, Australia

i had a similar noise from that area turns out my water pump bearing had gone and was causing the impaller to rattle slightly pump $80 $120 labour.
Top
 Profile  
 
 
Posted: Tue Oct 03, 2006 9:09 am 
Getting Side Ways
Offline
User avatar

Age: 44

Posts: 577

Joined: 5th Nov 2004

Ride: EF

Location: Wodonga
VIC, Australia

Another thing to check is the alternator bolts, if they are loose it will rattle around.
Also, If you get a long screw driver put one end on the power steering pump/alternator/water pump and the other on your ear you will easily find which is making the noise..
Top
 Profile  
 
 
Posted: Tue Oct 03, 2006 1:40 pm 
Getting Side Ways
Offline
User avatar

Posts: 887

Joined: 8th Aug 2006

Ride: Falcon

Location: Central Highlands
QLD, Australia

tjb45 wrote:
Another thing to check is the alternator bolts, if they are loose it will rattle around.
Also, If you get a long screw driver put one end on the power steering pump/alternator/water pump and the other on your ear you will easily find which is making the noise..



garden hose cut at a length of about 1m works alot better than a screwdriver, when locating noise problems.

 

_________________

97 EL Fairmont 4l OHC .Silver.
Exhaust: Pacemaker's, 2.5" exhaust and Hiflow cat
Intake: FRAM AIRHOG , EL GT snorkel
XR6 300kpa fuel reg Stg 2 Auto Shift Kit.6DJA ECU
PM in Qld looking too buy Toyota 4*4 SR5 Dualcab Hilux 91-97 with 2.8l diesel engine/5spd manual

Top
 Profile  
 
 
Posted: Tue Oct 03, 2006 5:23 pm 
Oompa Loompa
Offline

Posts: 39

Joined: 27th Jul 2006

Ride: Falcon

Location: melbourne
VIC, Australia

its been suggested to me that it might be the belt but since it was replaced new by a mechanic 3-4 years ago i thought that it might have something to do with a vane sticking in the pump but im no expert , thanks for the help, ill see what i can find.
Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 7 posts ] 

Who is online

Users browsing this forum: Google [Bot] and 75 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Tue Nov 26, 2024 4:29 pm All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names