|
| Patty |
|
||
|
hi im looking at obtaining some EF XR6 Door trims. I have a 96 EFII Gli and dont care much for power windows because i have no time to install them. So i figured ill buy some Xr6 trims and cut a hole in em for the winder.
Will the the winder fit as it (xr6 trim)has a different armrest. And as i have seen in the tech documents some clip has to be changed to fit the new trims... Is what i am planning to do possible... Thanks for ya help every1 |
||
| Top | |
||
| fairmont599 |
|
||
Posts: 1135 Joined: 27th Oct 2005 |
apparently the winder will hit on the new arm rest/handle bit. but i dont know as i have neither gli or xr
|
||
| Top | |
||
| twirqurky |
|
||
|
Meh, just do the power window conversion if you really want the trims in.
|
||
| Top | |
||
| Patty |
|
||
|
yeah ill probly just end up doing the conversion, just hate messing round with parts places , i just want to get the parts and get it done
too lazy lol thanks guys ill call some parts places 2moz |
||
| Top | |
||
| Mash85 |
|
||
|
rather than hack up the xr door trims, just swap the fabric insert over. once you take the door trim off you'll see the trim is held on by big clips, kinda like giant staples, just fold them back and the insert will pop out.
then swap it over to your gli door trims, should take 5 mins all up. no need to cut holes or anything messy
_________________
|
||
| Top | |
||
| Patty |
|
||
|
good thinking mash 85
im gunna do hte conversion but that trick saves me buying xr6 rear door trims thanks for all ya help everybody |
||
| Top | |
||
| Ballast |
|
|||
|
Patty wrote: good thinking mash 85
im gunna do hte conversion but that trick saves me buying xr6 rear door trims thanks for all ya help everybody I think that you will still end up buying the rear trims. Not many places like to seperate full sets of trims (ie selling the fronts and rears seperately) Nobody in their right mind would seperate the ccloth insert from the remainder of the trim, as it becomes very difficult to sell the remaining part of the trim. I have came across this problem recently, as I was looking for woodgrain for the door trims, nothing else. As a result, I had to buy a full set of NL ghia door trims 
_________________ Remember kids, the more pages of crap in your build thread, the bigger your e-penis is |
|||
| Top | |
|||
| au man |
|
|||
|
Why not just do the power window conversion, its better then window winders. Looks neater
|
|||
| Top | |
|||
| snap0964 |
|
|||
|
Find some fabric that you prefer, and cover the existing fabric inserts - don't remove the existing fabric as IIRC the padding is part of the fabric.
You can glue it to the insert rears using contact glue. You then can do front and rear inserts without buying whole door trims, etc at this stage. If you eventually go to power windows, you could then get the door trims to suit, be it just futura fronts, or fairmont/ghia/fairlane, etc and swap over the inserts if you prefer.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| stomper |
|
|||
|
i wanted to get the fairmont door trims as liked the them but i found out i have to get power winodws.
Ill do the conversion one day...When i have money.
_________________ HOLDENS go like rockets. They fall apart in stages!!! |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 80 guests |
