|
| XR6 EF |
|
|||
|
doin my head over christmas,will i need to replace exhaust and intake gaskets when i do the head gasket?i know i can use maniseal on the exhaust but dunno bout the intake, and does anyone know the approx price of a AU head gasket from fraud,went down today and they seem a bit pricey,Cheers all!!!
|
|||
| Top | |
|||
| stockstandard |
|
|||
|
bout $80 for the head gasket
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| XR6 EF |
|
|||
|
cheers mate, is the tightening sequence the same as ef gasket?
|
|||
| Top | |
|||
| snap0964 |
|
|||
|
XR6 EF wrote: is the tightening sequence the same as ef gasket? Yes.
You'll need a new inlet manifold gasket, they are normally around 2mm thick - your old one should just about fall off when the inlet is separated from the head, won't need much cleaning up (if any). Exhaust manifold is similar - you can reuse the std metal strip gasket, it might need a slight clean up
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| Krytox |
|
|||
|
tightening sequence: YES
Torque Specifications: NO
_________________ Carefree, we may not be number one, but we're up there. |
|||
| Top | |
|||
| smiley235 |
|
|||
|
Heres something I found very helpful when I changed my head gasket which my uncle told me (he used to fiddle with mustangs when he as in the US) each set of items you take off, put it and its bolts into a plastic bag and label what it is.
I made the mistake of not doing this when pulling apart my whole dash and when it was all back together, there were alot of bolts left over, who would have thought EA's could rattle even more.
_________________ 178.3 rwkw
|
|||
| Top | |
|||
| cjh |
|
|||
|
To do it properly, you should use new head bolts. Are you getting the cyl head skimmed for straight? Was it leaking coolant? What about corrosion of the head? what about new cyl head alignment dowels (2 of)?
What about new O'rings for the cam chain tensioner? There's more to it than " just change the head gasket", eh?
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| smiley235 |
|
|||
|
so right CJH, if you've got the cash, i'd even consider changing the internals to forged for longetivity and even boosted possiblilty, depends on what your after.
This is the condition of my head when I put it back on, it ran well until I sold it but i'm sure down the track it would be causing problems, get it recoed proffessionally. 
_________________ 178.3 rwkw
|
|||
| Top | |
|||
| XR6 EF |
|
|||
|
yeah bought the kit so have new intake and exhaust gaskets,got o-rings for the timing chain tensioner hopefully the head isn't warped as it hasn't overheated yet just noticed it was leaking a bit of coolant,
If it is i can get it machined by a mate for nothing.never heard of needind new dowels guess ill just wing it and hope i don't need em. Cheers for the input and the heads up on parts should go to plan hopefully,got most of it off last night should have it all done by lunch(as long as no machining is requires etc.) |
|||
| Top | |
|||
| XR6 EF |
|
|||
|
Oh yeah and motors only done 110 000ks and had headwork done by previous owner so should be in okay condition,i have acces to an acid bath if its is needed and no stranger to a bit of hard work so i don't think it'll need expert attention!!!(optimism at its best)never know till it all come off!lol
|
|||
| Top | |
|||
| JCaSs |
|
||
|
lol guys, i work for ford and the spare parts guys tell me never to buy stuff from em... i just finished doin my head gasket and head today n i picked up my head gasket and bolts for $50 from bursons.... although they did say 65 and i came with only 50 in cash so they sed dw about the rest.
_________________ EL GLi, DEV5 head, JMM race series extractors and exhaust.
|
||
| Top | |
||
| dsheps83 |
|
|||
|
smiley235 wrote: Heres something I found very helpful when I changed my head gasket which my uncle told me (he used to fiddle with mustangs when he as in the US) each set of items you take off, put it and its bolts into a plastic bag and label what it is.
I made the mistake of not doing this when pulling apart my whole dash and when it was all back together, there were alot of bolts left over, who would have thought EA's could rattle even more. i use my digital camera and take photos of where i take the s**t from for refernce if i cant remeber |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 77 guests |
