|
| NUTZEF |
|
||
|
jmm cams are $490 for a billet but for $122+$80 for shims and similar profiles are avalibale in regrind through wade. i just wont the biggest cam that will run with the stock computer as drivabilitly is not a massive issue. the 977b is suppose to run stock computer but advised computer upgrade so i could add a piggy back ecu later for more RWKW. does anybody have this cam in there car is so advice would be nice.
_________________ WOLF V500, t66(ar70 compressor), rochester 550cc injectors, borgg 265l fuel pump, 48mm turbosmart gate, turbosmart plumb back bov, 600x300x100 cooler, 3 inch zorst , 3.45 lsd, xr6 head, wade 1604 cam, adjustable cam gear, K&N pod filter, on 10psi and manual convertion exedy button clutch. 285.6rwkw |
||
| Top | |
||
| 66 coupe |
|
||
|
give chris (tensixty6) from wade a call / pm and get hold of one on the 1636977b grind cams, it is a new grind and does work well. Theres a thread on here somewhere with some feedbacl on the new profile.
|
||
| Top | |
||
| twr7cx |
|
|||
|
Considering the price difference I think the decision is a no brainer. Unless you can prove to me that the more than double spent on a JMM cam is going to give you 50% better results...
And if your paying $80.00 for shims then they are ripping you off. Genuine Ford spare parts only charged me $46.00 for a second set. |
|||
| Top | |
|||
| NUTZEF |
|
||
|
twr7cx what cam do u run and did u leave the standerd shims in and add a second set if so what size.
_________________ WOLF V500, t66(ar70 compressor), rochester 550cc injectors, borgg 265l fuel pump, 48mm turbosmart gate, turbosmart plumb back bov, 600x300x100 cooler, 3 inch zorst , 3.45 lsd, xr6 head, wade 1604 cam, adjustable cam gear, K&N pod filter, on 10psi and manual convertion exedy button clutch. 285.6rwkw |
||
| Top | |
||
| mitchg911 |
|
|||
|
or you could get some ford shims from a wrecker.. its not like they wear...
_________________ BF XR6T 6spd Auto. 60lb injectors, Hybrid Cooler, Custom Piping, Custom Surge Tank, Actuator. |
|||
| Top | |
|||
| stockstandard |
|
|||
|
NUTZEF wrote: jmm cams are $490 for a billet
Think you will find its a regrind not a billet
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| Sprjenkins |
|
||
|
JMM say its a billet, and you can't regrind a falcon cam to dev 5 size anyway
|
||
| Top | |
||
| twr7cx |
|
|||
|
NUTZEF wrote: twr7cx what cam do u run and did u leave the standerd shims in and add a second set if so what size.
Wade 1636. Yes you leave the standard shims in place, and just get a second set of standard shims, all your doing is doubling them up. |
|||
| Top | |
|||
| Steady ED |
|
|||
|
Sprjenkins wrote: JMM say its a billet, and you can't regrind a falcon cam to dev 5 size anyway
I beg to differ about dev5 being 'too big' for a regrind. And I've never heard of mock doing billets, especially not for the same price as their regrinds.
_________________ ED XR8 Sprint - S-Trim, V500, 249rwkw |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 41 guests |
