|
| huggiebear |
|
|||
|
hey all, as stated in my other thread im pulling the diff apart to get the gears out, but one of the axels is stuck, i got one side out with no problems but i have tried to get the other side out with no luck, i have tried jimmy bars (aka crowbar) mallets and all sorts but it just wont budge...
anyone got a trick or two in getting them out? or is it possible to wedge the gears out with one side still stuck inside |
|||
| Top | |
|||
| Krytox |
|
|||
|
rotor backwards and a few loose bolts.
slide hammer it with the disc.
_________________ Carefree, we may not be number one, but we're up there. |
|||
| Top | |
|||
| sexyr6 |
|
|||
|
get a stock rim put it on the axil backwards thred on two nuts about half way on and then use the rim like a slide hammer.. works every time for me..
_________________
|
|||
| Top | |
|||
| TwinturboBMX |
|
|||
|
sexyr6 wrote: get a stock rim put it on the axil backwards thred on two nuts about half way on and then use the rim like a slide hammer.. works every time for me..
Yep that is the easiest way and most recommended way to go about it, so easy we did that in a car park with minimal tools on a mates torana.
_________________ 17" Tezza Steelies, King F**king lows, pedders sports ryders, 2.5" cat back exhaust, pacemaker extractors, T5 manual
|
|||
| Top | |
|||
| huggiebear |
|
|||
|
cheers, ill give that a try. issue is its not on a car so ill have to drop it off the sawhorses and rest it on the ground to do it... i tried for over an hour
|
|||
| Top | |
|||
| 66 coupe |
|
||
|
also inspect the axle splines when you do get it out, if they are not dead straight, swap that axle for another, its probably got a bit of a twist in it.
|
||
| Top | |
||
| huggiebear |
|
|||
|
i wont be using these axles, ill be using the ones already in the LSD. as they look good condition. i just dont want to install the LSD with 2.77 gears
|
|||
| Top | |
|||
| huggiebear |
|
|||
|
well i got it... i tried how everyone said.. didnt work :@
so i got angry, stood it on the wheel and lifted the diff up and still nothing... in the end i lay'd it on the ground and done a running karate kick to it (while holding on to the swing set so i didnt end up on my head) and it got it off... it just needed 80kg of persuasion hahaha. nothing like some karate to start off your day... now nest question. how do i undo the shaft from the drive shaft to the back of the diff... i see there is a bolt but there is now nothing to stop it from spinning... maybe a long screwdriver through the hole... i dunno |
|||
| Top | |
|||
| huggiebear |
|
|||
|
im stuck with this at the moment..
how do i get that undone when there it nothing for it to grab onto... i thorght about a rope around the car somewhere and then attach it through the flange and try and undo the bolt that way... im out of ideas and need this out before friday. |
|||
| Top | |
|||
| Krytox |
|
|||
|
1: rattle gun
2: steel box section, drill 2 holes and bolt it up to the flange. mmm flange
_________________ Carefree, we may not be number one, but we're up there. |
|||
| Top | |
|||
| huggiebear |
|
|||
|
cheers ill give it a try... i wish i knew about that bolt before i removed the wheels... would of made my life 1 hell of alot easier...
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 88 guests |
