|
| Mac Winter 76XB351GS |
|
|||
|
Gday,
I have a fully forged and balanced clevo 383 stroker with a powerdyne, all new, 8.5CR. Im getting close to the set up stage now. Just wondering if anyone has supercharged something like this before and what would be a safe boost level? I will be running an intercooler and BOV (silent one) thru a mighty demon blow thru carb. Cheers, Matt
_________________ 76XBGS, 383c, custom crow cam, 4V p&p heads, Isky SS Valve+springs, extractors, 2.5"twins, MSD Ignition, Edelbrock intake, Forged bottom end, Barry Grant 750DP, thermo, discs, toploader, Holley fuel pump, SUPERCHARGED! |
|||
| Top | |
|||
| EBXR8380 |
|
|||
|
I'd say 8 Lb ...As you said safe..
It depends 100 % on tune... Seems small blower for big engine ???
_________________ As in ZOOM 126 edition |
|||
| Top | |
|||
| fritzz |
|
|||
|
will a powerdyne have enough to even supply 8lb to a clevo?
_________________ # 1997 EL Falcon GLI - 600+rwkw |
|||
| Top | |
|||
| EBXR8380 |
|
|||
|
{USERNAME} wrote: will a powerdyne have enough to even supply 8lb to a clevo?
Yea well ??? In this case where boost IS a restriction of flow.. It would have to be well over geared ??
_________________ As in ZOOM 126 edition |
|||
| Top | |
|||
| fritzz |
|
|||
|
yeh to small.
_________________ # 1997 EL Falcon GLI - 600+rwkw |
|||
| Top | |
|||
| balizticbobo |
|
|||
|
A bloke on AFF is selling his Vortech V4 trim off his Clevo, with all bracket etc.
Posted up in the Clevo section. Made 589hp @ 5000rpm, 12psi, 378 clevo.
_________________ 13.28@103.73mph |
|||
| Top | |
|||
| Mac Winter 76XB351GS |
|
|||
|
Not happy Jan!
I was told it would be good for 10pound, really only looking for 6...Too late now I already have it and no money left to change now. I'll have to see how it goes.
_________________ 76XBGS, 383c, custom crow cam, 4V p&p heads, Isky SS Valve+springs, extractors, 2.5"twins, MSD Ignition, Edelbrock intake, Forged bottom end, Barry Grant 750DP, thermo, discs, toploader, Holley fuel pump, SUPERCHARGED! |
|||
| Top | |
|||
| Mac Winter 76XB351GS |
|
|||
|
Since I have to get a main pulley made up I will get a slightly larger than stock one, to give a little bit more overdrive. As long as I make 500hp Im happy. Vortec can be a future mod. Just looked at the ad, says up to 20psi on a clevo....Its not the same one on the capa site either.
_________________ 76XBGS, 383c, custom crow cam, 4V p&p heads, Isky SS Valve+springs, extractors, 2.5"twins, MSD Ignition, Edelbrock intake, Forged bottom end, Barry Grant 750DP, thermo, discs, toploader, Holley fuel pump, SUPERCHARGED! |
|||
| Top | |
|||
| xr8ute |
|
||
|
If its the more common belt-driven BD-11A, then you might have to spin it pretty hard to make 500hp.
If its the larger gear-driven XB-1A then you should have no problems at all. There is another model as well thats in between those two size-wise. I dont know much about it though... Sounds like a fun project. Tune is everything. |
||
| Top | |
||
| Mac Winter 76XB351GS |
|
|||
|
Well its a bd11a... Im going to put it on and see how it goes. Having a supercharger thats not quite big enough is better than none at-all I spose.
As soon as funds permit I will get a vortech. Im so dissapointed that I got led up the path buying a powerdyne, I spose I could put it on my dirty magna 
_________________ 76XBGS, 383c, custom crow cam, 4V p&p heads, Isky SS Valve+springs, extractors, 2.5"twins, MSD Ignition, Edelbrock intake, Forged bottom end, Barry Grant 750DP, thermo, discs, toploader, Holley fuel pump, SUPERCHARGED! |
|||
| Top | |
|||
| xr8ute |
|
||
|
Just noticed this on fordforums, http://fordforums.com.au/showthread.php?t=107102
a J-Trim Vortech kit with Clevo brackets for 2900....might be worth a look. |
||
| Top | |
||
| Mac Winter 76XB351GS |
|
|||
|
Cheers, I wish Id known what I do now anout 3 weeks ago. Im out of cash at the moment. Hopefully it is still for sale by the time im ready.
_________________ 76XBGS, 383c, custom crow cam, 4V p&p heads, Isky SS Valve+springs, extractors, 2.5"twins, MSD Ignition, Edelbrock intake, Forged bottom end, Barry Grant 750DP, thermo, discs, toploader, Holley fuel pump, SUPERCHARGED! |
|||
| Top | |
|||
| Mac Winter 76XB351GS |
|
|||
|
Just found a set of bearings that can spin up to 60 000 rpm instead of the standard 36000rpm and a kevlar belt to suit. Im going to put them in the powerdyne and gear it up a bit. Should get the 8+ pound im after no worries. I'll post up how it goes.
Id still rather a vortech but this is a whole lot cheaper and will get the same result im after...just without quite as much headroom.
_________________ 76XBGS, 383c, custom crow cam, 4V p&p heads, Isky SS Valve+springs, extractors, 2.5"twins, MSD Ignition, Edelbrock intake, Forged bottom end, Barry Grant 750DP, thermo, discs, toploader, Holley fuel pump, SUPERCHARGED! |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 11 guests |
