|
Froudey |
|
||
|
Yeah the manual should be in on friday night or saturday morning yeh me!!! it should of been done in sunday but i went to that warwick farm deally.... was good!
A question regarding conversion the AUTO TCM unit sits were the clutch should be so i assume i would be removing it but do i trace the TCM loom and remove that aswell?? Wiring should i just follow voxace's guide minus the risitors and plug... cheers Geoff
_________________ R.I.P Tobias my son. Last edited by Froudey on Sat Aug 18, 2007 9:38 pm, edited 1 time in total. |
||
Top | |
Froudey |
|
||
|
http://www.fordmods.com/forums/viewtopi ... 315#700315
another thread i started maybe some one can help me?
_________________ R.I.P Tobias my son. |
||
Top | |
Froudey |
|
||
|
Hey Folks just an Update..... I got the Flywheel, clutch, pressure plate, G'Box, Tailshaft, starter motor in and clutch pedal,
i just got to install the radiator and shorud etc etc fill up with oil and coolant, tighten some bolts and she will be a manual (yippee) i have started to write a doco on it just got to finished it off tomorrow night and i will post it up
_________________ R.I.P Tobias my son. |
||
Top | |
Froudey |
|
||
|
Help Car not starting i removed the tcm, and removed the round plug and turned the other loom into the reverse switch and nuetral switch car not starting
_________________ R.I.P Tobias my son. |
||
Top | |
Nicko |
|
|||
|
{USERNAME} wrote: Help Car not starting i removed the tcm, and removed the round plug and turned the other loom into the reverse switch and nuetral switch car not starting
So have you shorted out the neutral switch so car thinks its in neutral to start?
_________________ Nicko |
|||
Top | |
Froudey |
|
||
|
{USERNAME} wrote: {USERNAME} wrote: Help Car not starting i removed the tcm, and removed the round plug and turned the other loom into the reverse switch and nuetral switch car not starting So have you shorted out the neutral switch so car thinks its in neutral to start? no i havn't how do ya do that
_________________ R.I.P Tobias my son. |
||
Top | |
Froudey |
|
||
|
I found this on that ford-tech doco....
Quote: So, find the starter relay, then on pin 86 (read the underside of the relay) you should find two orange/black wires (colour and number may vary - PLEASE make sure you know which relay it is!). Cut these wires off an earth the ones on the relay side of the cut. I just soldered a wire to them and ran it round to the negative terminal on the battery, but a screw thru the body somewhere should work just as well.
Now, the car should start!
_________________ R.I.P Tobias my son. |
||
Top | |
Froudey |
|
||
|
Bump
_________________ R.I.P Tobias my son. |
||
Top | |
Froudey |
|
||
|
Bump
_________________ R.I.P Tobias my son. |
||
Top | |
ToranaGuy |
|
|||
|
For the wiring to fool the car to thinking the auto is in neutral, wouldn't the car need to have the TCM still fit up?
Cheers ToranaGuy
_________________ I am the ToranaGuy!|74 Lh Torana Turbo|78 Hz PanelVan|86 Mighty Boy Ute|93 EB2 Ghia,GT Mockup,5spd,LPGI,Full Leather|2 x EB Xr8 5spd's|{DESCRIPTION}|{DESCRIPTION}|{DESCRIPTION}| |
|||
Top | |
Froudey |
|
||
|
The other thing that my starter dropped down off the sway bar while me and dad grabbed a drink.... would this of damaged the starter....
does any one have a picture or diagram of the wiring of the manual switches cheers
_________________ R.I.P Tobias my son. |
||
Top | |
Who is online |
---|
Users browsing this forum: No registered users and 49 guests |