|
| jjohnno |
|
||
|
Get my power cables from inside the car, to the battery under the bonnet?
I've read somewhere that i should use the clutch cable hole (its a ED fairmont auto) Is there anywhere else i can run them? |
||
| Top | |
||
| FordFairmont |
|
||
Posts: 6113 Joined: 8th May 2007 |
Whats wrong with the clutch cable hole?
|
||
| Top | |
||
| phongus |
|
|||
|
you can run the cable through the wiring grommet. though you will need to either cut a hole in the grommet to squeeze the cable through, or remove the grommet, pass the cable through the hole, then try and push the grommet back in the hole with the cable being squashed...I prefer the former.
Since your car is an auto...I refer to FordFairmont's question above me. phong =P~
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| Andrew J |
|
|||
|
you can actually run it down the side of the drivers guard and through a grommet in the side of the footwell if you prefer? I think thats where it is...
_________________ The problem with America is stupidity. I'm not saying there should be a capital punishment for stupidity, but why don't we just take the safety labels off of everything and let the problem solve itself?
|
|||
| Top | |
|||
| joolz |
|
|||
|
{USERNAME} wrote: you can actually run it down the side of the drivers guard and through a grommet in the side of the footwell if you prefer? I think thats where it is...
Thats how i ran mine, i found it alot neater than the firewall (clutch cable hole) option. All thats seen is some cable running in front of the battery past behind the headlight into the guard cavity. |
|||
| Top | |
|||
| HornDog |
|
|||
|
{USERNAME} wrote: you can actually run it down the side of the drivers guard and through a grommet in the side of the footwell if you prefer? I think thats where it is... thats the best spot if not the clutch cable
|
|||
| Top | |
|||
| Shum's EL |
|
|||
|
follow the bonnet release cable
|
|||
| Top | |
|||
| krisisdog |
|
|||
|
{USERNAME} wrote: follow the bonnet release cable
thats what i did in the ef, and made the hole bigger and fitted an apropriate grommet n a touch of silicone to seal it. |
|||
| Top | |
|||
| jjohnno |
|
||
|
thanks for the help guys.
I am not sure if it was the clutch cable hole, but it was directly about the foot rest pedal and has a black plug on the engine side. A perfectly sized hole for 4gauge 
one last question, how do i go about connection it to the battery? |
||
| Top | |
||
| Shum's EL |
|
|||
|
yeah that's the clutch cable hole
connect it to the battery with one of these - 
|
|||
| Top | |
|||
| jjohnno |
|
||
|
I don't think my crimper will do it haha
I didn't know you could be those connectors to fit 4gauge wire? |
||
| Top | |
||
| Shum's EL |
|
|||
|
yeah most wiring kits come with that terminal on the battery end
|
|||
| Top | |
|||
| stomper |
|
|||
|
You can use those gold ring terminals as above and use a standard crimper with one of the grooves in the middle of the ring connector
or You can spend $30 on a gold terminal from jaycar and bolt it straight onto that.
_________________ HOLDENS go like rockets. They fall apart in stages!!! |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 15 guests |
