|
| millard455 |
|
|||
|
hi all, my dramas continue
 some how when i was fitting my new stainless intake pipe i must have hit the maf sensor on the powersteer filler tube and broke a small hole in the plastic cover, yeah i know im a d***head. will this cause it to idle s**t? im guessing it will. now ive never removed the maf sensor from the maf so bare with me if im not making much sence here. is the maf sensor 1 piece once its renoved from the maf
ie, can i just replace the black plastic cover or am i up for a complete new maf sensor?? many thanks in advance.
_________________ EL XR8 SERIES 2, 5SPD, HOT CHILLI RED, 200 ODD RWKW OF V8 FUN AND GAMES |
|||
| Top | |
|||
| XR9UTE |
|
||
|
Unless you damaged the circuitry inside you will have no problems. Just stick a bit of black silicone in the hole.
|
||
| Top | |
||
| millard455 |
|
|||
|
{USERNAME} wrote: Unless you damaged the circuitry inside you will have no problems. Just stick a bit of black silicone in the hole.
ok cool, ill give that a go and get her going thisarvo and see how she runs. i was looking around today to find a replacement and i found this bloke who has 7 brandnew genuine ford maf's for $230 each but he says they suit eb-el v8. can anyone confirm that eb-el v8s have the same maf?
_________________ EL XR8 SERIES 2, 5SPD, HOT CHILLI RED, 200 ODD RWKW OF V8 FUN AND GAMES |
|||
| Top | |
|||
| AU220UTE |
|
||
|
just had a new one installed on my ute, $450 a nice surprise in the service
|
||
| Top | |
||
| millard455 |
|
|||
|
well didnt get round to fixing it today, that can be tomorows mission.
i thaught i might aswell pull it apart and give the hot wires a clean while im fixing it and im just wondering if there is anything i should look out for when removing the sensor? once i undo the litle torx bits does it just slide out? i realy dont wana break anything else so any advice would be great. thanks
_________________ EL XR8 SERIES 2, 5SPD, HOT CHILLI RED, 200 ODD RWKW OF V8 FUN AND GAMES |
|||
| Top | |
|||
| XR9UTE |
|
||
|
{USERNAME} wrote: {USERNAME} wrote: Unless you damaged the circuitry inside you will have no problems. Just stick a bit of black silicone in the hole. ok cool, ill give that a go and get her going thisarvo and see how she runs. i was looking around today to find a replacement and i found this bloke who has 7 brandnew genuine ford maf's for $230 each but he says they suit eb-el v8. can anyone confirm that eb-el v8s have the same maf? Yes unless you have a GT or a Sprint which have a 70mm. |
||
| Top | |
||
| Scaffy |
|
|||
|
Just unscrew and pull out. It's quite simple - even I've done it! Ha!
_________________ Trickflow Street Heat top end kit, 70mm BBK TB & EGR, 24lb injectors, Underdrives & 3.73s: 275rwhp - 13.15@105mph NA / 12.37@116mph N20 |
|||
| Top | |
|||
| millard455 |
|
|||
|
{USERNAME} wrote: Just unscrew and pull out. It's quite simple - even I've done it! Ha!
thats what i like to hear, nice and easy. fixed that hole, thanks very much xr9ute, realy didnt wana buy a new one as im only gona upgrade it this time next year when i put some new heads on, selastic worked a treat and i glued a small piece of hard black plastic over the selastic just to make sure.
_________________ EL XR8 SERIES 2, 5SPD, HOT CHILLI RED, 200 ODD RWKW OF V8 FUN AND GAMES |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 15 guests |
