|
| ghia97 |
|
||
|
How hard is it to replace the welsh plugs on the exaust manifold side the top two closest to power steering pump?
|
||
| Top | |
||
| Krytox |
|
|||
|
very easy, drop the coolant, carefully punch them in, remove them with multi-grips, clean the holes, replace with new ones and use stag or form-a-gasket (hardening type) .. strongly advise to replace all welsh plugs.
_________________ Carefree, we may not be number one, but we're up there. |
|||
| Top | |
|||
| Shortshift |
|
|||
|
Ditto the above. If you've got extractors, it will be easy. But if you've got the original manifold on and can't get access with a drift & hammer, it's got to come off. Make sure you don't knock them inside the block. Replacements should be brass for longevity. I use a socket that fits nicely inside the welsh plug and tap it lightly. Try to get them started at about 90 degrees to the block.
_________________ AU2 XR8 with Raptor VL, ported Yella Terra GT40P heads, Scorpion 1.6 RRs, XE264HR-14 Comp Cam, ceramic coated Hurricane Headers, 60lb injectors, Walbro 255, 200cfi cats, 3" exhaust & Snow Performance water methanol injection |
|||
| Top | |
|||
| cjh |
|
|||
|
Theres 8 welsh plugs all up, all 40mm. 5 on the exhaust side, 1 at reat of the block ( remove tranny and flexpate/flywheel and backing plate ), and 2 on the inlet manifold side. To do these, the in man and dizzy have to come off to do them. I use Loctite 272 to fit the welsh plugs, sets in about 5 mins. Lightly sand the brass welsh plugs first to take off the smooth finish on the sealing surface.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| ghia97 |
|
||
|
Thanks guys, is it possible as they are corroded to screw a screw in and pull it out. Is loctite a suitable sealant for the brass plugs? i have bought a set for the side but all look good except to of them so i was just gonna change them till i get the hang of it. Cheers
|
||
| Top | |
||
| cjh |
|
|||
|
ghia97 wrote: Thanks guys, is it possible as they are corroded to screw a screw in and pull it out. Is loctite a suitable sealant for the brass plugs? i have bought a set for the side but all look good except to of them so i was just gonna change them till i get the hang of it. Cheers
Loctite suitable??? Sh!t yeah, if you spill some on your fingers and hold the brass welsh plug, give it about 45 secs, and it starts to stick like supa-glue. Used it for years and no probs.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| ghia97 |
|
||
|
Thanks wasnt sure, can i do damage to engine by being rough pulling it out?
|
||
| Top | |
||
| horis |
|
|||
|
no champ just hit on one edge tap them in and pull them out you aint goona hurt anything you got a cast iron block
_________________ 95 ef montfor sale pm for info, 88 hilux mud truck |
|||
| Top | |
|||
| ghia97 |
|
||
|
Thanks ill give it a go. Dont know why they couldnt be made more easily accessable. How long should it take? Cheers
|
||
| Top | |
||
| Hybrid34 |
|
||
|
MAKE sure you get brass or coopa
_________________ Sucessful trades with Schmee, Braidy, Niko, The_Ghost, YBHVE4, Stalker
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 154 guests |
