|
| halo |
|
||
|
as above, i have an ea and the intake is part of the plastic shround covering the fan, radiator etc (moulded on to the plastic)
how do i remove it so that i can put a bigger snorkel on? i was thinking sanding it down but that will take forever by hand, cutting it with a saw would leave uneven lines, and then i thought maybe melt it off with a soldering iron but mmm nah i tried that on my door and long story short my door looks f**k as.. any advice?
_________________ the rearing serpent sports in the mists
|
||
| Top | |
||
| naughtyfalcon |
|
|||
|
cut it with a hack saw blade or blow the car up.lol
_________________
|
|||
| Top | |
|||
| Shortshift |
|
|||
|
I use a 4 inch grinder with diamond cutting wheel to occasionally cut plastics. Then just use a fine file to clean it up. And yes, I know the plastic melts but if you're careful it works fine.
Otherwise, as naughtyfalcon said, use a hacksaw.
_________________ AU2 XR8 with Raptor VL, ported Yella Terra GT40P heads, Scorpion 1.6 RRs, XE264HR-14 Comp Cam, ceramic coated Hurricane Headers, 60lb injectors, Walbro 255, 200cfi cats, 3" exhaust & Snow Performance water methanol injection |
|||
| Top | |
|||
| ringastinga |
|
||
|
or as naughty said blow it up half stick of dynamite should do it cheaper option is the sodabulb bomb
|
||
| Top | |
||
| alfy |
|
|||
|
carbon-arc gouge it
... or not lol
_________________ 2021 V6 Manual Amarok - 245kw/750nm - many goodies |
|||
| Top | |
|||
| fordman351 |
|
|||
|
Get rid of the clutch fan all together, turf the fan shroud, obtain EF-EL thermo fans and wiring kit from a performance shop. That will solve the chunky fan shroud problem and will give you a truckload more engine response and a slight increase in power. Then think about EF-AU dual plane manifold and airbox.
But if all this is too complex, i suggest what has been suggested, an angle grinder haha. |
|||
| Top | |
|||
| halo |
|
||
|
ive already got an ef box, i have got the hole to the bbm fiberglassed up, i am running the TB piping into the existing hole that the ef snorkel originally went into, i have cut a hole to fit an xh snorkel in
i just need to buy some 3 inch piping tmorrow so that i can mount the pod on an angle that will fit in the box, and cut another 3 inch hole in the bottom or side so i can run more 3" piping to suck in more air most likely from under the car. i will pursue the thermo fan idea otherwise saw it off and file it back
_________________ the rearing serpent sports in the mists
|
||
| Top | |
||
| frankieh |
|
|||
|
I chopped up my old airbox and grafted it to a battery box bottom using mostly an angle grinder.. works fine.
|
|||
| Top | |
|||
| fordfreak ef |
|
|||
|
hack saw with fine teeth.. then use sanpaper to smoothen out the rough cut... to give that "Factory" look....
|
|||
| Top | |
|||
| Brett3158 |
|
||
|
You can probably replace the whole shroud with that off
EB2 which has the seperate intake. |
||
| Top | |
||
| halo |
|
||
|
decided im gonna do the thermofan conversion with the help of bunter then i can just screw the snorkel down on top. killing 2 birds with one stone.
_________________ the rearing serpent sports in the mists
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 41 guests |
