|
| ef_paddy |
|
||
|
Hey guys,
Not quite sure what happened to the last thread where i was asking questions about lowering... seems to have disappeared. Well i've decided to go with king lows Monroe GT Sport Lowered Shocks: http://cgi.ebay.com.au/Ford-Falcon-EF-E ... dZViewItem and a camber kit... will this one do the job? http://cgi.ebay.com.au/Ford-EA-EB-ED-EF ... dZViewItem There's another thread getting around where the bloke has replaced all the nolothane bushes on his car and it has done wonders for the feel and handling of the car so it seems like a good idea... i was wondering if there was a kit i could buy online? Cheers in advance for your help and advice guys. Pat
_________________ "You only need 2 tools, WD-40 and duct tape. If it doesnt move and it should, use WD-40. If it moves and it shouldnt, use the duct tape!" |
||
| Top | |
||
| joolz |
|
|||
|
The shocks are only a new addition to the Monroe range but have the same performance as the original GT Gas but with a shortened body. They should be fine but please let us know how they go.
I have the same camber/castor kit in my EL. That are great and have plenty of adjustment. Mine havnt budged since installed. I got mine from Repco for $175 so try them first. |
|||
| Top | |
|||
| wild_ef |
|
|||
|
the guys that lowered my car said a camber kit is a waste of money on low springs.
and are only really needed on superlows onwards
_________________ BA Fairmont Ghia |
|||
| Top | |
|||
| JOSE |
|
|||
|
yet i was once told by pedders i needed them to install one for $250 on my car because it was "almost out of camber adjustment)
_________________ Because i can. |
|||
| Top | |
|||
| ef_paddy |
|
||
|
Haha trust pedders....
Well if that's the case about the camber kit i can save myself a few hundred that can pay for my diff gears. I will let you know how the shocks are when i get them in about a month. Does anyone have any opinion on these shocks? Are these the best value for this dollar range? Cheers, Pat
_________________ "You only need 2 tools, WD-40 and duct tape. If it doesnt move and it should, use WD-40. If it moves and it shouldnt, use the duct tape!" |
||
| Top | |
||
| EB92 |
|
|||
|
Would recommend you stick with the camber kit. It's only
the cost of the part, as installation takes place with everything else. There is a 'shim type' which may be a little cheaper than the one you have nominated. Part No. is 45146 by Nolathane. Whether or not a kit is required will always be a different argument from whoever is setting up the front end. My bloke likes to set the front with -1.0 deg camber. I have driven both this and the standard. The corners tell the story. If you are spending some dough and opening up the front end anyway, why do it on the cheap ?? |
|||
| Top | |
|||
| ef_paddy |
|
||
|
EB92 good point... I am doing it on cheap as far as sourcing parts at the best price i can find... I was wondering if the camber kit did do alot for handling on the fords? You reckon -1 degree? I'm still looking for somewhere online other than ebay that sells all the nolathane parts i need.
_________________ "You only need 2 tools, WD-40 and duct tape. If it doesnt move and it should, use WD-40. If it moves and it shouldnt, use the duct tape!" |
||
| Top | |
||
| EB92 |
|
|||
|
It can be difficult when different advice or suggestions are getting
thrown around on the best way to do something. I've certainly found this to be the case, but my mechanic has always told me..... "Take your time with the research and then do it once and do it right". Kits have worked well for me, with both handling improvements and reduced tyre wear. I'm not sure about other online parts sources, but you can get price quotes from say Autobarn or Repco and they will order it. Al the best with your project. |
|||
| Top | |
|||
| Allan Gray |
|
||
|
is it hard to install a camber kit or should it be done by a suspension joint
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 23 guests |
