|
| braidy |
|
|||
|
Hey guys,
At work at this is annoying the crap out of me so I am trying to work it out. Threw a new amp in, wired it up (i do alot of this stuff, so I know what I am doing) and it blew the blade fuses in the amp the second I connected the positive to the battery. Car was not on or anything. Got some more blade fuses, as they start to contact, they blow. I know the ground is good, metered at the amp terminals and am getting 12v or aroundabout anyways. Note, THESE FUSES BLOW WHEN THE AMP IS OFF. I had the thought of a short. My problem with this theory is, why wouldn't the inline fuse blow. Is it possible it doesn't blow and the amp fuses do because of their lower current rating? Need help urgently, frustrating the crap out of me.
_________________ RIP Chelsea |
|||
| Top | |
|||
| grub73 |
|
|||
|
what amp ??
_________________ EF XR6 5spd 14.57@97mph |
|||
| Top | |
|||
| braidy |
|
|||
|
Some piece of crap US Audio thing.
_________________ RIP Chelsea |
|||
| Top | |
|||
| Disco Frank |
|
|||
|
well if the amp fuse is rated at 10A and inline is rated at 15A then of course the amp fuse will blow
but im guessing there would be a problem with the amp itself could be a loose wire in it also check the connections for the speakers
_________________ RIP SCOTT |
|||
| Top | |
|||
| braidy |
|
|||
|
Connection to speakers are fine. So is it possible that its a short somewhere along the positive line? I wouldn't have thought that would blow the amp fuses though.
F**k amp?
_________________ RIP Chelsea |
|||
| Top | |
|||
| outlawxr6 |
|
|||
|
The problem CANNOT be in the power wiring otherwise the inline fuse would blow not the amps fuse so if the amps fuse is blowing then it can only be 1 of 2 things, the first is that the power is hooked up a*** about + to - and vice versa or the amp is shorted internally. Amps have a big diode that effectively presents a dead short if the polarity is back to front to prevent damage to the amp, maybe this diode is shagged or was assmebled incorrectly....
_________________ Do it once, Do it right!!!!!! |
|||
| Top | |
|||
| gros20 |
|
||
|
a fuse/cb in theory will blow close as possible to the scourse if fuses are teh same.
what sort of fuse are they? use multimeter and measure reistaance between + and - with nothing connected. |
||
| Top | |
||
| s-tranzor |
|
|||
|
make sure none of your speakers have shorts to ground either. Most amps' speaker outputs float above earth due to push-pull design and use +ve/-ve internal rails. can s**t up if a short or something occurs.
|
|||
| Top | |
|||
| krisisdog |
|
|||
|
Well to start with I'd connect only the power wires, no speakers.
Double check you have the pos and neg correct. If the fuse still blows then your amp is fuked. Also you're meant to remove the main power fuse when youre installing amps, not just the amps fuse. |
|||
| Top | |
|||
| maximus |
|
|||
|
Trigger/remote wire connected to ground by mistake?
Disconnect all speakers for the next test. The problem is definately in or on the amp iteslf.
_________________ Subtle but high quality audio system. |
|||
| Top | |
|||
| outlawxr6 |
|
|||
|
gros20 wrote: a fuse/cb in theory will blow close as possible to the scourse if fuses are teh same.
what sort of fuse are they? use multimeter and measure reistaance between + and - with nothing connected. Using a meter on the terminals won't prove anything due to diodes and filter caps etc on the 12v side of the amp. If it is blowing fuses as soon as the fuse is inserted without the remote powered then the problem is inside the amp!
_________________ Do it once, Do it right!!!!!! |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 22 guests |
