Fordmods Logo

setting isc & gearbox 

 

Page 1 of 1 [ 6 posts ] 

 
 Post subject: setting isc & gearbox
Posted: Sat Nov 01, 2008 4:21 pm 
Stock as a Rock
Offline

Posts: 142

Joined: 26th Mar 2007

Location: bowral
NSW, Australia

dose any body know were i can find the doc were i can set the isc & gearbox at the same time its something like were you have the reds on then off and put the gearbox in park then drive if any one can tell me as for the life of me i cant find it any were as i have seen it before
Top
 Profile  
 
 
Posted: Sat Nov 01, 2008 5:55 pm 
Getting Side Ways
Offline
User avatar

Age: 35

Posts: 1448

Joined: 17th Apr 2008

Gallery: 3 images

Ride: VY Commodore Wagon Accli

Location: Bannockburn
VIC, Australia

What Car are you trying to attempt this on?

 

_________________

Pre AU Adapters for sale

Successful Trades with: John_XR6 (John_LS1), Private9, Schmee, Manari, Kyle_Bardell, Greenhorn (Boostedfalcon.net), FTG AUTO SALVAGE, EVL098, Gogetta, EFIII, Krytox, Blue, Smik-EL, TP351.

Top
 Profile  
 
 
Posted: Sat Nov 01, 2008 8:48 pm 
Stock as a Rock
Offline

Posts: 142

Joined: 26th Mar 2007

Location: bowral
NSW, Australia

sorry my ef
Top
 Profile  
 
 
Posted: Sun Nov 02, 2008 10:08 am 
Stock as a Rock
Offline

Posts: 142

Joined: 26th Mar 2007

Location: bowral
NSW, Australia

any body
Top
 Profile  
 
 
Posted: Sun Nov 02, 2008 10:25 am 
Fordmods Newbie
Offline

Posts: 9

Joined: 9th Mar 2008

Location: Sydney
NSW, Australia

Instructions from the EF & EL Workshop Manual:

Any time the battery is disconnected, the transmission must re-learn the closed and wide-open throttle positions to enable the PCM to determine the proper gear to select for the appropriate throttle position. If the calibration is not performed following power source interruption, the transmission will shift hard and perform poorly from then on.

So to calibrate as follows:

First of all drive the car to normal engine temp and the thermostat has opened etc
Then to verify the correct idlespeed of the engine the following 4 steps should be taken with the vehicle being idled while stationary for approx 1-2 minute in each of the following conditions.
NOTE- DO NOT TOUCH THE ACCELERATOR DURING ANY PERIOD OF THE 5 FOLLOWING ADAPTIVE PROCESSES.

1. Neutral with all electrical loads OFF.
2. Neutral with Air conditioning ON.
3. *Drive with all electrical loads OFF.
4. *Drive with Air conditioning ON.

After all this has been done then proceed to go on and to do these steps which actually set the TPS values;

5. *To set the closed throttle referance position , place the transmission
in Drive, Air con off, and let the engine idle for a minimum of 1 minute.
6. Next, set the wide-open throttle reference position by turning the
engine off- but leave the ignition switch to the "ON," position, ie;Idiot lights on etc, then press the accelerator
pedal to the floor and hold it their for 1 minute, minimum.
7. Then Place the gear selector to Park and switch off the ignition.
8. Drive the vehicle and check for proper shifting patterns.

*As a clarifying note, I guess that for steps 3, 4 & 5 you can place the car in D with the handbrake firmly applied.

 

_________________

Gunmetal EF XR6 Auto
Silhouette SX GHIA AWD

Top
 Profile  
 
 
Posted: Sun Nov 02, 2008 10:54 am 
Stock as a Rock
Offline

Posts: 142

Joined: 26th Mar 2007

Location: bowral
NSW, Australia

thank you thats what i need
Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 6 posts ] 

Who is online

Users browsing this forum: No registered users and 65 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Fri Nov 29, 2024 7:07 am All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names