|
| hans hartman |
|
||
|
Punnisher_42 wrote: Hey hans - you reckon you could punctuate your messages? they are so hard to read!!! will try,but thinking and typing-then have another tip,have to almost do a draft first to make it simple and informative.doing it and writing about are different.you have to have a basic idea.
_________________ R.I.P HANS HARTMAN |
||
| Top | |
||
| green machine |
|
|||
|
why did you use acrylic over 2pac, 2pac gives a much better finish.
and i say you might of used to much thinners to! you can mix it to your own liking unless you use hardener (which is only in 2pac). and when spraying the last coat always spray it alittle heavier then the others so you get a smooth finish, just watch for runs on the sharper edges.
_________________ custom airbox,custom intake |
|||
| Top | |
|||
| EF_STOCKO |
|
||
|
I used Acrylic as it was suggested to be easier.
Plus apparently you need an oven booth or some s**t for 2pac.. Ive seen home jobs with Acrylic come out with brilliant shine. I will get their I suppose. Just a hurdle. |
||
| Top | |
||
| green machine |
|
|||
|
i only spray in 2pac and i don't use a booth or oven. you use hardener instead of the booth or oven.
there is more work in acrylic then 2pac as if you spray 2pac right there is no buffing or sanding to do after you finish and you get a deeper shine then acrylic. but yeah you will get there in the end just rub it down with 1200 wet and give it one heavy coat but watch for runs.
_________________ custom airbox,custom intake |
|||
| Top | |
|||
| Slick |
|
|||
|
hans hartman wrote: id say your mix is wrong 1.5 clear\1 thinners,you ran it dry due too to much thinners,the paint dried before it hit the panel,try some thinners only and wet it,it may melt the dry spray and flaten it,other wise wet sand with a lot of water,1500 grit and a block,the paints still wet and will take aweek to dry and longer,when its smooth and clean,recoat with 1-2 coats, as you will take a few coats off sanding the dry stuff,when you recoat,spray wet as possible,small runs can be sanded out.use a tac rag to remove over spray dust,do sides and doors 1st,then boot,bonnet,roof as they are half each side,spray boot and let it dry for half hour so over spray wont stick easily,you will see what i mean and will be glossy.
That's correct, if you're dusting the clear coat on you'll end up with that dull sandy feel to the paint. try and slow your passes over the surface so you'll leave a wet shiny finish on the pass.
_________________ Mind f**k!!! it works on feeble minded ignorant sheeples... there's plenty of em on this site... some are very intelligent but by god they are so thick!!! Pakrat wrote: You can buy them seppertly
|
|||
| Top | |
|||
| EF_STOCKO |
|
||
|
Apon sanding, I realised there was a very thick layer of clear laid down. So I wet sanded starting with 1200 and finishing with 1500.
I then got the buffer out and used meguires medium cut and polish all round. I then applied meguires swirl remover, and then the showcar finishing wax and it has come up pretty damn good. The sides were especially nice, with the roof needing a bit more attention. But yeah, very happy with how it is coming out. Could be a little less "Dull" but I am sure with a bit more polishing it will come out. Cheers guys.. Will post a pic when I find my camera chord. |
||
| Top | |
||
| PIMP_LTD |
|
||
|
Nice work EF-STOCKO. Have seen many "not lookin great" jobs that have come up pretty smick with a bit of this work.
_________________ Commodore australia's favorite car??? What a load of s**t |
||
| Top | |
||
| Slick |
|
|||
|
Yeah man, good work EF-STOCKO!!!
post up some pics of the finish goods soon. your next respray down the line will be much better. I guarantee you that! I know when I did my first job years ago. there was a lot of rubbing back! LOL
_________________ Mind f**k!!! it works on feeble minded ignorant sheeples... there's plenty of em on this site... some are very intelligent but by god they are so thick!!! Pakrat wrote: You can buy them seppertly
|
|||
| Top | |
|||
| GTO13F |
|
||
|
u need 2 cut back ur base colour b4 spraying clear coat 2 get optimum shine after clearing and yer a hit with the buff a few weeks after the clears dried should b like a mirror with colour in the background.
_________________ EF futura in the build.
|
||
| Top | |
||
| EF_STOCKO |
|
||
|
Ok guys,
I ended up being so dissapointed with the first paint job, I painted it again haha!!! Anyhow, here it is.. Just needs a light sand, buff and polish in a few weeks when the clear settles. Im a lot happier with this effort rather than the first! I added a lot more thinners to the clear, and after I sprayed the clear there were a little bit of dry spots still (dont know how), but I tackled them with a slight spray of thinners, and Job Done !!!! 
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 131 guests |
