|
raff-26 |
|
|||
|
hey all, after a long drive I noticed the horrible smell of coolant leaking onto extractors- after an awful time under a hot engine bay I discovered it was the inlet hose for the gas converter that was corroded at the t pipe just behind upper inlet.
This was all ok, disconnect heater tap hose bring coolant hose above upper manifold and cut off and replace. All was fine until today and I smelled that familiar smell again!!!! This time its the hose (small one) from the upper manifold- and appears to end down at the lower manifold- which from what i can make out needs to have the upper manifold removed to access screw clamp my hands nor my two year olds hands would have no hope of fitting! BOTH ends are slightly leaking!! Being a jungle of tubes behind the old HO I think I may as well replace all of them - but would t know where to start- and with nanna just passing on, and a recent house move well I just don't have the patience! ! All tubes are full of rust grit too, as the previous owner ran the engine on a diet of tap water!!! Should I do anything else while I get it done (ie: save for some gt40p's and exploer upper/lower as I am guessing the head/ manifold water jackets will be much the same as internals of hoses!!! Maybe I should adopt the phrase of "dont fix it if it aint broke" if so how much should i expect to pay to get all hoses at back done?? do the hoses come as a pack? cheers
_________________ EF Ghia 5L V8 |
|||
Top | |
TerroristGHIA |
|
|||
|
The little hose you refer to, does that go to the back of the TB, if so, it can be just run from manifold to manifold, it is a heater for cold weather and stops the TB freezing. They must be brought individually as far as i know.
Brett
_________________ The Terrorist ED Retired due to RUST. |
|||
Top | |
raff-26 |
|
|||
|
yes brett its the one that runs from back of throttle housing to the lower inlet mani- Doe's the upper need to be removed to access lower screw clamp?? I cant work a way to get in there...
_________________ EF Ghia 5L V8 |
|||
Top | |
TerroristGHIA |
|
|||
|
From memory, i used a small socket, bout 4 or 5mm and undid it that way. But i would suggest you remove the upper, then you can just run it to the other side of the manifold. It isnt that hard to remove the upper, althought the last bolt at the back can be a pain due to the firewall being in the way. Goodluck
Brett
_________________ The Terrorist ED Retired due to RUST. |
|||
Top | |
One Drone |
|
|||
|
EGR hose. Can even block it off if you want. IF you have small asian hands like me it's fine to get in there without removing upper.
_________________ There are 10 types of people in this world. |
|||
Top | |
raff-26 |
|
|||
|
{USERNAME} wrote: EGR hose. Can even block it off if you want. IF you have small asian hands like me it's fine to get in there without removing upper.
correct me if I'm wrong...but I dont think the EGR hose leaks coolant?
_________________ EF Ghia 5L V8 |
|||
Top | |
TerroristGHIA |
|
|||
|
That hose goes to the back of the EGR. 1 in and 1 out. Thats what drone was refering to
Brett
_________________ The Terrorist ED Retired due to RUST. |
|||
Top | |
mitchg911 |
|
|||
|
{USERNAME} wrote: {USERNAME} wrote: EGR hose. Can even block it off if you want. IF you have small asian hands like me it's fine to get in there without removing upper. correct me if I'm wrong...but I dont think the EGR hose leaks coolant? its the EGR heater hose.. and yep its a coolant hose.. used to warm the EGR plate for emissions reasons... personally i didnt like the idea of it warming my ingoing air so i bypassed it..
_________________ BF XR6T 6spd Auto. 60lb injectors, Hybrid Cooler, Custom Piping, Custom Surge Tank, Actuator. |
|||
Top | |
TerroristGHIA |
|
|||
|
^^^^ Same here
Brett
_________________ The Terrorist ED Retired due to RUST. |
|||
Top | |
raff-26 |
|
|||
|
i still cant work a way behind the upper manifold to take off that egr hose at the bottem where it is split...i think i am going to have to take off the upper, may as well change them all.
any pointers? I have never attempted to even remotely take apart a windsor... I am guessing i need a torque wrench for bolt torques for upper to lower?
_________________ EF Ghia 5L V8 |
|||
Top | |
vrblou02 |
|
|||
|
that little coolant hose we are talking about i just finished replacing
was tight and had to get my hand in on the passenger side just in front of the heater hoses and go in from there once i got it started was done in 10 mins but brett as u say u just bypassed it? can u explain a little please i thought it would have been needed my car was going through a bit of coolant with that hose split so glad its all done now can it be simply blocked? mines fixed now so not worried but it may help out others in the future cheers folks Drifty
_________________ THE V8 OUTLAW |
|||
Top | |
COBRAED |
|
|||
|
{USERNAME} wrote: that little coolant hose we are talking about i just finished replacing Yes it can be blocked Drifty, thats what i done to mine also.
was tight and had to get my hand in on the passenger side just in front of the heater hoses and go in from there once i got it started was done in 10 mins but brett as u say u just bypassed it? can u explain a little please i thought it would have been needed my car was going through a bit of coolant with that hose split so glad its all done now can it be simply blocked? mines fixed now so not worried but it may help out others in the future cheers folks Drifty Jason. |
|||
Top | |
TerroristGHIA |
|
|||
|
With the upper off, you will see where it goes to. What i mean is that the is 2 inputs at the back of the EGR, so to bypass it, i went from the manifold to the manifold, instead of manifold to EGR, then EGR to manifold, if you can understand what i mean.
As for a torque wrench, not necessary, just nip them up, then 1/4 extra turn and they are done. Be careful with the hose at the base of the rear of the upper that goes to the PCV, this can cause issues if it doesnt come out cleanly from the lower. Cheers and good luck Brett
_________________ The Terrorist ED Retired due to RUST. |
|||
Top | |
vrblou02 |
|
|||
|
thanks jason an brett
hope this helps u along ur way a little raff best a luck bud Drifty
_________________ THE V8 OUTLAW |
|||
Top | |
COBRAED |
|
|||
|
No worries mate.
Jas. |
|||
Top | |
Who is online |
---|
Users browsing this forum: No registered users and 14 guests |