|
| izedso |
|
|||
|
Hope someone can shed some light on this one.
My EF keeps blowing LH Headlight Globes(getting very expensive replacing crystal vision globes) I am uber careful when changing globes, I never touch the glass at all. The RH one has been going fine for ever. Just the low beam H1 in the LHS keeps goin. The headlight was replaced before I got the car (so the lights are clear not yellow) the high beam and parkers never fail either. Any ideas?? Bad earth?? Where should I start?
_________________
|
|||
| Top | |
|||
| kevman |
|
||
|
Bad connections ,vibration[loose retaining clip],bad earth.
|
||
| Top | |
||
| Krytox |
|
|||
|
Most likely the globe is vibrating as above!
_________________ Carefree, we may not be number one, but we're up there. |
|||
| Top | |
|||
| Froudey |
|
||
|
are the plugs intact no sign of melting or anthing other then that i would say either the earth or power to the headlight globe may have the slighest tear or cut in the insulation and causeing a fault.
_________________ R.I.P Tobias my son. Last edited by Froudey on Fri Jan 16, 2009 6:36 pm, edited 1 time in total. |
||
| Top | |
||
| izedso |
|
|||
|
Thanks guys, I will take a look tomorrow. Vibration seems possible. Hope to god its not in the wiring.
_________________
|
|||
| Top | |
|||
| EF Wagon |
|
|||
Posts: 69 Joined: 27th Dec 2006 Ride: EF Wagon Location: Canberra - not as bad as you think |
Try changing brands of Globes. I've found the stuff they are selling in the big chains to be not so good quality.
My EF had the same problem as yours and I switched to Phillips brand globes with no problems since. I'd stay with Phillips or Hella.
_________________ 96 EF Wagon, PRINS VSI LPG, Wade 1636, 4480's, Redback zorst, Metalcat, 3 angle valve job, .5mm overbore, hypertec pistons, shaved head (because the head was banana shaped when I brought it), Tickford 16" alloys, KYB shocks, 30mm sway bar, 1 1/2 degrees negative camber, tow bar, roof racks. |
|||
| Top | |
|||
| izedso |
|
|||
|
EF Wagon wrote: Try changing brands of Globes. I've found the stuff they are selling in the big chains to be not so good quality.
My EF had the same problem as yours and I switched to Phillips brand globes with no problems since. I'd stay with Phillips or Hella. I am using Philips Crystal Vision Globes. Too expensive to keep killin em'
_________________
|
|||
| Top | |
|||
| izedso |
|
|||
|
**UPDATE**
Its seems to be an electrical gremlin... Headlight working sometimes, but found out that RH tail light flickers(and my dash has done it since day 1, but I thought that was a bad led conversion) Any ideas on where to start looking? It has a brand new battery & terminals. And my AFR gauge works fine using the earth direct to battery.
_________________
|
|||
| Top | |
|||
| alfy12 |
|
|||||
|
I have seen numerous failures of the 3 pin plug at the bulb itself. Suggest you get a new plug and solder/heatshrink it a few inches down the wires from the original connection. You could also crimp some new spade connections onto the existing wired but this has the disadvantage of having to know which pin on the bulb each spade connector goes to.
The connectors fail where the wire is crimped onto each female spade connection. This leads to melting plugs and excessive heat at the back of the bulb. New connectors can be purchased from most larger auto parts stores or your local auto electrician. I have included an example of what you want to buy.
_________________ NF Fairlane: Non Factory Dual Fuel - New coolant tank, New fuel injectors, New fuel pump, New earth cable, ECU capacitors replaced, New O2 sensor, leads and plugs, New Radiator/Condensor cleaned. 483,000kms. AU I6 Powered. Struts, Shockies, Tie rods and ball joints replaced. |
|||||
| Top | |
|||||
| Who is online |
|---|
Users browsing this forum: andryt and 123 guests |
