|
| joel08 |
|
||
|
wanted a AU head gasket for a EL 4L
|
||
| Top | |
||
| Krytox |
|
|||
|
go to ford.
last one i bought 3 months ago was $65
_________________ Carefree, we may not be number one, but we're up there. |
|||
| Top | |
|||
| joel08 |
|
||
|
ah nice one thanks mate.
was just on the ford site trying to find it.. no luck |
||
| Top | |
||
| gogetta |
|
|||
|
ive got a 2nd hand used one u can have cheap
_________________ |
|||
| Top | |
|||
| EL_lagoon |
|
||
|
Why would u use an AU head gasket for an EL, are they less prone to leaking?
how well do they fit? ive got an EL with a leaking head gasket as well just lookin for a bit of advice thanks mate |
||
| Top | |
||
| joel08 |
|
||
|
from what i know the au's have the better alloy gaskets.
|
||
| Top | |
||
| KWIKXR |
|
|||
|
AU gaskets are thinner and therefore can raise the comp ratio
|
|||
| Top | |
|||
| phongus |
|
|||
|
EL_lagoon wrote: Why would u use an AU head gasket for an EL, are they less prone to leaking? how well do they fit? ive got an EL with a leaking head gasket as well just lookin for a bit of advice thanks mate AU gaskets are made up of 3 layers of metal which are stronger then composite ones you get for E-series. AU gaskets will also increase compression as someone has mentioned, but if you are not there for POWAH, then it wouldn't really bother you. AU gasket will last you longer over an E-series composite gasket...I don't think there are many E-series out there that actually still have the original head gasket. phong =P~
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| KWIKXR |
|
|||
|
Very good info ^^^^ there Phong
|
|||
| Top | |
|||
| Shortshift |
|
|||
|
Just to play the Devil's Advocate.... a local cylinder head reconditioner said he's had complaints about the AU metal gaskets. Apparently, they don't seal well when the head and/or deck aren't machined prior to installation. He recommends Dura Tec gaskets instead. The last head gasket I had was a MonoTorque & that was still OK after 160,000k (till I put a modified head on).
In spite of that, I haven't heard any negative feedback on this site about AU metal gaskets.
_________________ AU2 XR8 with Raptor VL, ported Yella Terra GT40P heads, Scorpion 1.6 RRs, XE264HR-14 Comp Cam, ceramic coated Hurricane Headers, 60lb injectors, Walbro 255, 200cfi cats, 3" exhaust & Snow Performance water methanol injection |
|||
| Top | |
|||
| joel08 |
|
||
|
mate thats the sort of feed back we need..
cheers shortshift |
||
| Top | |
||
| gogetta |
|
|||
|
yeah deck surface has to be very well cleaned. the gasket is less tolerant to imperfections than regular gaskets
also they do not tolerate poor cooling system maintenance
_________________ |
|||
| Top | |
|||
| alfy |
|
|||
|
phongus wrote: EL_lagoon wrote: AU gasket will last you longer over an E-series composite gasket...I don't think there are many E-series out there that actually still have the original head gasket. phong =P~ *Ghia raises hand* 
_________________ 2021 V6 Manual Amarok - 245kw/750nm - many goodies |
|||
| Top | |
|||
| Krytox |
|
|||
|
AU MLS gaskets for the win.
I wouldn't use ANY non-multi layer gasket, its all about expansion. All these cars that go to mechanics that slap in a $50vrs kit, only come back within 100,000k's. Downside with AU gaskets are the compression raising. Good for some, bad for others. You can expect some pinking if you've machined the head a few times.
_________________ Carefree, we may not be number one, but we're up there. |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 45 guests |
